Time yet again for another kit review. Today’s kit is the Larson Scanner from Evil Mad Science. What a different name for a company; their byline is “DIY and open source hardware for art, education and world domination”. Art? Yes. Education? Definitely. World domination? Possibly – you could use the blinking LEDs to hypnotise the less intelligent world leaders out there.
Anyhow, what is a Larson Scanner? Named in honour of Glen A. Larson the creator of television shows such as Battlestar Galactica and Knight Rider – as this kit recreates the left and right blinking motion used in props from those television shows. For example:
The kit itself is quite inexpensive, easy to assemble – yet can be as complex as you want it to be. More about that later, for now let’s put one together and see how it performs. There are two versions of the kit, one with 5mm clear LEDs and our review model with 10mm diffused red LEDs. The kit arrives inside a huge resealable anti-static bag, as such:
Upon opening the bag we have the following parts (there was an extra LED and resistor, thanks):
… the PCB:
… which is nicely done with a good silk-screen and solder mask. And finally:
A very handy item – a battery box with power switch. The kit is powered by 2 x AA cells (not included!). And finally, the instructions:
At this point you can see that this kit is designed for the beginner in mind. The instructions are easy to read, clear, and actually very well done. If you are looking for a kit to get someone interested in electronics and to practice their soldering, you could do a lot worse than use this kit. Construction was very easy, starting with the resistors:
followed by the capacitor and button:
then the microcontroller:
… no IC socket. For a beginners’ kit, perhaps one should have been included. Next was the battery box. Some clever thinking has seen holes in the PCB to run the wires through before soldering into the board – doing so provides a good strain relief for them:
… and finally the LEDs. Beginners may solder them in one at a time:
however it is quicker to line them up all at once than solder in one batch:
… which leaves us with the final product:
Operation is very simple – the power switch is on the battery box. The button on the PCB controls the speed of LED scrolling, and if held down switches the brightness between low and high. Now for some action video of the Larson Scanner in operation:
Well that really was fun, a nice change from the usual things around here.
After sitting my Larson Scanner next to the computer tower for a few minutes, I had contemplated fitting it into a 5.25″ drive bay to make my own Cylon PC, however that might be a little over the top. However my PC case has some dust filters on the front, which would allow LEDs to shine through in a nicely subdued way. Mounting the Larson Scanner PCB inside the computer case will be simple, and power can be sourced from the computer power supply – 5V is available from a disk drive power lead.
If you are going to modify your PC in a similar fashion, please read my disclaimer under “boring stuff” first.
The Larson Scanner can run on 3.3V without any alteration to the supplied components. What needs to be done is to use a voltage regulator to convert the 5V down to 3.3V. My example has used a 78L33 equivalent, the TI LP2950 as it is in stock. The power comes from a drive power cable splitter as such:
You may have a spare power plug in your machine, so can tap from that. 5V is the red lead, and GND is the adjacent black lead. Don’t use yellow – it is 12V. It is then a simple matter of running 5V from the red lead to pin 1 of the regulator, GND from the Larson Scanner and PC together to pin 2, and 3.3V out from the regulator to the PCB 3.3V. Insulation is important with this kind of work, so use plenty of heatshrink:
… then cover the whole lot up:
Now to locate a free power plug in the machine. It has been a while since opening the machine – time for a dust clean up as well:
Mounting the PCB is a temporary affair until I can find some insulated mounting standoffs:
However it was worth the effort, the following video clip shows the results in action:
So there you have it. The Larson Scanner is an ideal kit for the beginner, lover of blinking LEDs, and anyone else that wants to have some easy blinking fun. You can buy Larson Scanner kits in Australia from Little Bird Electronics, or directly from Evil Mad Science for those elsewhere.
As always, thank you for reading and I look forward to your comments and so on. Furthermore, don’t be shy in pointing out errors or places that could use improvement. Please subscribe using one of the methods at the top-right of this web page to receive updates on new posts, follow me on twitter or facebook, or join our Google Group for further discussion.
High resolution images are available on flickr.
[Note – The kit was purchased by myself personally and reviewed without notifying the manufacturer or retailer]
Latest posts by John Boxall (see all)
- First Look – Arduino M0 Pro with 32 bit ARM Cortex M0 - October 28, 2015
- Control your Arduino over the Internet using Blynk - September 20, 2015
- Experimenting with Arduino and IKEA DIODER LED Strips - September 19, 2015