Old Kit Review – Diesel Sound Simulator for Model Railroads

Introduction

In this review of an older kit (circa 1993~1997) we examine the Diesel Sound Simulator for Model Railroads kit from (the now defunct) Dick Smith Electronics, based on the article published in the December 1992 issue of Silicon Chip magazine.

The purpose of this kit is to give you a small circuit which can fit in a HO scale (or larger) locomotive, or hidden underneath the layout – that can emulate the rumbling of a diesel-electric locomotive to increase the realism of a train. However the kit is designed for use with a PWM train controller (also devised by Silicon Chip!) so not for the simple direct-DC drive layouts.

K3030 diesel sound simulator kit

Assembly

The diesel sound kit was from the time when DSE still cared about kits, so you received the sixteen page “Guide to Kit Construction” plus the kit instructions, nasty red disclaimer sheet, feedback card, plus all the required components and the obligatory coil of solder that was usually rubbish:

K3030 diesel sound simulator kit contents

Everything required to get going is included, except IC sockets. My theory is it’s cheaper to use your own sockets than source older CMOS/TTL later on if you want to reuse the ICs, so sockets are now mandatory here:

K3030 diesel sound simulator kit parts

The PCB is from the old school of “figure-it-out-yourself”, no fancy silk-screening here:

K3030 diesel sound simulator kit PCB

K3030 diesel sound simulator kit PCB bottom

Notice the five horizontal pads between the two ICs – these were for wire bridges in case you needed to break the PCB in two to fit inside your locomotive.

Actual assembly was straight-forward, all the components went in without any issues. Having two links under IC2 was a little annoying, however a short while later the PCB was finished and the speaker attached:

K3030 diesel sound simulator kit finished

How it works

As mentioned earlier this diesel sound kit was designed for use with the Silicon Chip train PWM controller, so the design is a little different than expected. It can handle a voltage of around 20 V, and the sound is determined by the speed of the locomotive.

The speed is determined by the back EMF measured from the motor – and (from the manual) this is the voltage produced by the motor which opposes the current flow through it and this voltage is directly proportional to speed.

Not having a 20V DC PWM supply laying about I knocked up an Arduino to PWM a 20V DC supply via an N-MOSFET module and experimented with the duty cycle to see what sort of noises could be possible. The output was affected somewhat by the supply voltage, however seemed a little higher in pitch than expected.

You can listen to the results in the following video:

I reckon the sound from around the twenty second mark isn’t a bad idle noise, however in general not that great. The results will ultimately be a function of a lower duty-cycle than I could create at the time and the values of R1 and R2 used in the kit.

 Conclusion

Another kit review over. With some time spent experimenting you could generate the required diesel sounds, a Paxman-Valenta it isn’t… but it was a fun kit and I’m sure it was well-received at the time. To those who have been asking me privately, no I don’t have a secret line to some underground warehouse of old kits – just keep an eye out on ebay and they pop up now and again. Full-sized images and much more information about the kit are available on flickr.

And while you’re here – are you interested in Arduino? Check out my new book “Arduino Workshop” from No Starch Press.

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

The following two tabs change content below.

John Boxall

Founder, owner and managing editor of tronixstuff.com.

4 Responses to “Old Kit Review – Diesel Sound Simulator for Model Railroads”

  1. XBox says:

    Woah this web site is extremely good everyone loves understanding your content regularly. Be on the great do the job! You no doubt know, lots of people are hunting game due to this details, you are able to guide them significantly.

  2. Michael says:

    Hi there,

    I used to own one of these kits, no idea where it is nowadays, but the sound coming out of yours is nothing like what the kit should produce. The kit should make a very hearty rumble that oscillates at about 1Hz representing the slow idling of a diesel, and then as you increase the motor speed a turbo whine should kick in.

    I never really got the turbo effect of mine to kick in as it was a somewhat temperamental circuit, but I’d suggest you go back and double check all the components and solder joints, and check your ICs are socketed correctly. I’d also suggest adding a real motor so that it can pick up the back EMF.

    I had mine hooked up to an old 8 inch speaker and the bass was deafening. When set up correctly you should almost have a Paxman sounding simulation.

    –Michael

    • John Boxall says:

      Thanks Michael. Nice website.
      I recall going over it a few times but it went with my last batch of giveaways, so too late to revisit. I can well imagine it working, there are/were a lot of train nuts at SC.

Trackbacks/Pingbacks


Leave a Reply

Receive notifications of new posts by email.

The Arduino Book

Arduino Workshop

Für unsere deutschen Freunde

Dla naszych polskich przyjaciół ...

Australian Electronics!

Buy and support Silicon Chip - Australia's only Electronics Magazine.

Use of our content…

%d bloggers like this: