Archive | combination lock

Project – Ultrasonic Combination Switch

In this project you learn how to make an ultrasonic distance-sensing combination switch.

Updated 18/03/2013

Time for a follow-up to the Single Button Combination Lock by creating another oddball type of switch/lock. To activate this switch we make use of a Parallax Ping))) Ultrasonic sensor, an Arduino-style board and some other hardware – to make a device that receives a four-number code which is made up of the distance between a hand and the sensor. If Arduino and ultrasonic sensors are new to you, please read this tutorial before moving on.

The required hardware for this project is minimal and shown below – a Freetronics Arduino-compatible board, the Ping))) sensor, and for display purposes we have an I2C-interface LCD module:

The combination for our ‘lock’ will consist of four integers. Each integer is the distance measured between the sensor and the user’s hand (etc.). For example, a combination may be 20, 15, 20, 15. So for the switch to be activated the user must place their hand 20cm away, then 15, then 20, then 15cm away. Our switch will have a delay between each measurement which can be modified in the sketch.

To keep things simple the overlord of the switch must insert the PIN into the switch sketch. Therefore we need a way to take measurements to generate a PIN. We do this with the following sketch, it simply displays the distance on the LCD):

And here is a demonstration of the sketch in action:

Now for the switch itself. For our example the process of “unlocking” will be started by the user placing their hand at a distance of 10cm or less in front of the sensor. Doing so will trigger the function checkPIN(), where the display prompts the user for four “numbers” which are returned by placing their hand a certain distance away from the sensor four times, with a delay between each reading which is set by the variable adel. The values of the user’s distances are stored in the array attempt[4].

Once the four readings have been taken, they are compared against the values in the array PIN[]. Some tolerance has been built into the checking process, where the value entered can vary +/- a certain distance. This tolerance distance is stored in the variable t in this function. Each of the user’s entries are compared and the tolerance taken into account. If each entry is successful, one is added to the variable accept. If all entries are correct, accept will equal four – at which point the sketch will either “unlock” or display “*** DENIED ***” on the LCD.

Again, this is an example and you can modify the display or checking procedure yourself. Moving forward, here is our lock sketch:

To finish the switch, we housed it in the lovely enclosure from adafruit:

And for the final demonstration of the switch in action. Note that the delays between actions have been added for visual effect – you can always change them to suit yourself:

So there you have it – the base example for a different type of combination switch. I hope someone out there found this interesting or slightly useful.

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in adafruit, arduino, combination lock, DFR0063, enclosure, hardware hacking, parallax, ping, projects, ultrasonic2 Comments

Project – Single button combination lock

Time for something different  – a single button combination lock. Allow me to explain…

Updated 18/03/2013

Normally a combination lock would require the entry of a series of unique numbers in order to unlock something or start an action. For example:

800px-masterpadlock

(image information)

A more contemporary type of lock could be controlled electronically, for example by a keypad where the user enters a series of digits to cause something to happen. Such as the keypad on this dodgy $30 safe from Officeworks:

As you can see there is a button for each digit. You would think that this would be a good idea –  however people can watch you enter the digits, or users can be silly enough to write down the combination somewhere. In some cases the more cunning monkeys have even placed cameras that can observe keypads to record people entering the combination. There must be a better way. Possibly! However in the meanwhile you can consider my idea instead – just have one button. Only one button – and the combination is made up of the time that elapses between presses of the button. There are many uses for such an odd lock:

  • A type of combination lock that controls an electric door strike, or activates a device of some sort;
  • A way of testing mind-hand coordination for skill, or the base of a painfully frustrating game;
  • Perhaps an interlock on motor vehicle to prevent drink driving. After a few drinks there’s no way you could get the timing right. Then again, after a double espresso or two you might have problems as well.
How does it work? Consider the following:

We measure the duration of time between each press of the button (in this case – delay 1~4). These delay times are then compared against values stored in the program that controls the lock. It is also prudent to allow for some tolerance in the user’s press delay – say plus or minus ten to fifteen percent. We are not concerned with the duration of each button press, however it is certainly feasible.

To create this piece of hardware is quite easy, and once again we will use the Arduino way of doing things. For prototyping and experimenting it is simple enough to create with a typical board such as a Uno or Eleven and a solderless breadboard – however to create a final product you could minimise it by using a bare-bones solution (as described here). Now let’s get started…

For demonstration purposes we have a normally-open button connected to digital pin 2 on our Arduino-compatible board using the 10k ohm pull down resistor as such:

democircuit

The next thing to do is determine our delay time values. Our example will use five presses, so we measure four delays. With the following sketch, you can generate the delay data by pushing the button yourself – the sketch will return the delay times on the serial monitor:

So what’s going on the this sketch? Each time the button is pressed a reading of millis() is taken and stored in an array. [More on millis() in the tutorial]. Once the button has been pressed five times, the difference in time between each press is calculated and stored in the array del[]. Note the use of a 500 ms delay in the function dataCapture(), this is to prevent the button bouncing and will need to be altered to suit your particular button. Finally the delay data is then displayed on the serial monitor. For example:

The example was an attempt to count one second between each press. This example also illustrates the need to incorporate some tolerance in the actual lock sketch. With a tolerance of +/- 10% and delay values of one second, the lock would activate. With 5% – no. Etcetera.

Now for the lock sketch. Again it measures the millis() value on each button press and after five presses calculates the duration between each press. Finally in the function checkCombination() the durations are compared against the stored delay values (generated using the first sketch) which are stored in the array del[]. In our example lock sketch we have values of one second between each button press. The tolerance is stored as a decimal fraction in the variable tolerance; for example to have a tolerance of ten percent, use 0.1:

When choosing your time delays, ensure they are larger than the value used for button debounce (the delay() function call) in the dataCapture() function. Notice the two functions success() and failure() – these will contain the results of what happens when the user successfully enters the combination or does not. For a demonstration of the final product, I have connected an LCD to display the outcomes of the entry attempts. You can download the sketch from here. The key used in this example is 1,2,3,4 seconds:

Although there are four buttons on the board used in the video, only one is used. Well I hope someone out there found this interesting or slightly useful…

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, combination lock, education, learning electronics, lesson, microcontrollers, millis, projects, tutorial, twitter6 Comments


Subscribe via email

Receive notifications of new posts by email.

The Arduino Book

Arduino Workshop

Für unsere deutschen Freunde

Dla naszych polskich przyjaciół ...

Australian Electronics!

Buy and support Silicon Chip - Australia's only Electronics Magazine.

Use of our content…

%d bloggers like this: