Tag Archive | "12"

Arduino and KTM-S1201 LCD modules

Learn how to use very inexpensive KTM-S1201 LCD modules in this edition of our Arduino tutorials. This is chapter forty-nine of a series originally titled “Getting Started/Moving Forward with Arduino!” by John Boxall – A tutorial on the Arduino universe. The first chapter is here, the complete series is detailed here.

Introduction

After looking for some displays to use with another (!) clock, I came across some 12-digit numeric LCD displays. They aren’t anything flash, and don’t have a back light –  however they were one dollar each. How could you say no to that? So I ordered a dozen to try out. The purpose of this tutorial is to show you how they are used with an Arduino in the simplest manner possible.

Moving forward – the modules look like OEM modules for desktop office phones from the 1990s:

With a quick search on the Internet you will find a few sellers offering them for a dollar each. The modules (data sheet) use the NEC PD7225 controller IC (data sheet):

They aren’t difficult to use, so I’ll run through set up and operation with a few examples.

Hardware setup

First you’ll need to solder some sort of connection to the module – such as 2×5 header pins. This makes it easy to wire it up to a breadboard or a ribbon cable:

The rest of the circuitry is straight-forward. There are ten pins in two rows of five, and with the display horizontal and the pins on the right, they are numbered as such:

Now make the following connections:

  • LCD pin 1 to 5V
  • LCD pin 2 to GND
  • LCD pin 3 to Arduino D4
  • LCD pin 4 to Arduino D5
  • LCD pin 5 to Arduino D6
  • LCD pin 6 to Arduino D7
  • LCD pin 7 – not connected
  • LCD pin 8 – Arduino D8
  • LCD pin 9 to the centre pin of a 10k trimpot – whose other legs connect to 5V and GND. This is used to adjust the contrast of the LCD.

The Arduino digital pins that are used can be changed – they are defined in the header file (see further on). If you were curious as to how low-current these modules are:

That’s 0.689 mA- not bad at all. Great for battery-powered operations. Now that you’ve got the module wired up, let’s get going with some demonstration sketches.

Software setup

The sketches used in this tutorial are based on work by Jeff Albertson and Robert Mech, so kudos to them – however we’ve simplified them a little to make use easier. We’ll just cover the functions required to display data on the LCD. However feel free to review the sketches and files along with the controller chip datasheet as you’ll get an idea of how the controller is driven by the Arduino.

When using the LCD module you’ll need a header file in the same folder as your sketch. You can download the header file from here. Then every time you open a sketch that uses the header file, it should appear in a tab next to the main sketch, for example:

headerinuse

There’s also a group of functions and lines required in your sketch. We’ll run through those now – so download the first example sketch, add the header file and upload it. Your results should be the same as the video below:

So how did that work? Take a look at the sketch you uploaded.  You need all the functions between the two lines of “////////////////////////” and also the five lines in void setup(). Then you can display a string of text or numbers using

which was used in void loop(). You can use the digits 0~9, the alphabet (well, what you can do with 7-segments), the degrees symbol (use an asterix – “*”) and a dash (use  – “-“). So if your sketch can put together the data to display in a string, then that’s taken care of.

If you want to clear the screen, use:

Next – to individually place digits on the screen, use the function:

Where n is the number to be displayed (zero or a positive integer), p is the position on the LCD for the number’s  (the positions from left to right are 11 to 0…), d is the number of digits to the right of the decimal point (leave as zero if you don’t want a decimal point), and l is the number of digits being displayed for n. When you display digits using this function you can use more than one function to compose the number to be displayed – as this function doesn’t clear the screen.

To help get your head around it, the following example sketch (download) has a variety of examples in void loop(). You can watch this example in the following video:

Conclusion

So there you have it – an incredibly inexpensive and possibly useful LCD module. Thank you to Jeff Albertson and Robert Mech for their help and original code.

LEDborder

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, display, education, ktm-s101, ktms101, LCD, lesson, part review, pd7225, tutorialComments (10)

Kit review – ogi lumen Nixie Tube system

Hello readers

Time to finish off the month with a fascinating kit review  – the ogi lumen nixie tube system. The younger readers amongst us may be thinking “what is a nixie tube?” Here is an example of four in a row:

p1080918

If you cast your mind back to before the time of LCDs, and before LEDs… to the mid-1950s. Nixie tubes were used to display data in various forms on electrical devices, from test equipment, scales, elevator indicators, possible doomsday machines, clocks – anything that required visual output would be a candidate. Although nixie tubes are now totally out of date, as with many things there is a growing trend to use them again, for cool retro-style, nostalgia and those people who enjoy living in the past.

How nixie tubes work is quite simple, an element is within a vacuum tube full of gas, such as neon. When a high-voltage (~190 volts DC) current flows through the element, it glows. For more information, here is a great explanation. You will note that they are similar to in look but different in design to the vacuum-fluorescent displays, as used in the ice tube clock reviewed a few months previously. The tubes used in this kit are the Soviet model IN-12A:

p1080865

The IN-12A tube can display the digits zero to nine, with a nice orange glow.  For the uninitiated, sourcing and making nixie tubes can be quite difficult. Apart from procuring the tubes themselves, you need a suitable power supply and logic ICs that can handle the higher voltage to control the tubes. Thankfully Ogi Lumen have put together a system of kits to make using these nixie tubes simple and interesting. There are three components to the system, the first being the power supply:

p1080879

Note that the power supply is preassembled. This supply can generate the necessary 150 to 220 volts DC to energise our nixie tubes. Yes – up to 220 volts! For example:

p1080922

However the current required is quite small – one power supply can handle up to twenty-four IN12A nixie tubes. My example in the photograph above is drawing 110~120 milliamps from a 12V DC supply. For those of you assembling these kits, please be careful. It can be easy to physically move the kit about whilst in operation, and touching the live HV pads will hurt a lot. After bumping the HV line on the PCB, my whole left arm went into a spasm and hurt for the time it took to see my doctor. So be careful.

The second item required is the driver kit. This is a board that takes care of the shift-registers and power for two of the nixie tubes. Driver kits can be slotted together to form a row of nixie tubes. The third and final item is the nixie duo kit. This contains two IN-12A tubes, matching sockets and a PCB to muont them. This PCB then slots into the driver kit PCB. You can buy the driver and duo kit as a set for a discount.

From a hardware perspective, assembling the kits is relatively simple. There isn’t any tricky soldering or SMD to worry about, however you will need a lot of solder. The contents of the duo and driver kits are as follows:

p1080869

Before you start soldering, please download and take note of the instructional .pdf files available for the duo and driver board kits. Assembling the driver kit (on the right) is very straight forward. However – please read the instructions! An interesting part of note is the K155ИД1IC:

p1080872

This is the Russian equivalent of the 74141. This is a BCD-decimal decoder IC that can handle the high voltages required for nixie tubes. When soldering the resistors, take care with R2 – it will need to be positioned horizontally so as to not rub against the duo board:

p1080934

When it is time to assemble the duo board, you will need time and patience. At a first glance, one would imagine that the sockets drop into the PCB, and the nixie tubes will happily be seated into the sockets. This is not so, don’t solder in the sockets first! The pins on the bottom of the socket also form part of the socket for the tube legs – which can alter the positioning of the socket legs. Make sure you have the socket with pin 1 at the top of the PCB. After some trial and error, the best way to insert the tubes is to first partially place the sockets into the PCB:

p1080880

… then fully insert the tubes into their sockets. Make sure the tube is the right way up – check that the digit 3 in the tube is the right way up. Then push the whole lot into the PCB. At this point you should check to make sure the sockets are in line with each other:

p1080892

(Notice how thick the PCB is…) At which point you can solder them in, followed by the row of connector pins:

p1080896

By this stage you will need some fresh air from all that soldering. The PCB holes for the socket pins really take a lot. Now you can connect the power supply to the driver board and give the tubes a test-toast:

p1080941

All the tubes should have their elements glowing. This is a good start. The next step is to connect the appropriate microcontroller and start displaying. As noted in the instructions, the 74141 BCD-decimal ICs are controlled by standard 74HC595 shift-register ICs, so your microcontroller needs to send out a data, clock and latch line. My following examples have been created using the Ardiuno system and a compatible board.

The first example is a method of displaying integers. It uses the Nixie library which you can download here.

That was just an arbitrary demonstration to get some numbers displayed. Here is a short video clip of it in action:

Now for another, more useful example. By using a DS1307 real-time clock IC with the Arduino, we can make a nice clock that displays the time and date. For more information on using the DS1307 with Arduino, please visit this tutorial. You can download the example nixie clock .pde file from here. And finally, here is the clock in action:

The problem with these tubes is that you will never have enough. Already I have thought of a few things to make that require a lot more tubes, so in the next month or so stay tuned to tronixstuff.com as there will be more projects with these kits.

In conclusion, this was a great kit and anyone looking to use some numerical nixie tubes will do very well with the Ogi Lumen products. Furthermore the designs are released under Creative Commons by-sa-nc, and the files are available to download from the product pages. And finally, it is a lot of fun – people will generally ask you about the tubes as they may have never seen them before.

Remember, if you have any questions about these modules please contact Ogi Lumen via their website. Higher resolution images available on flickr.

Have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

[Note – the kit assembled in this article was received from Ogi Lumen for review purposes]

Posted in arduino, kit review, learning electronics, nixie, ogilumenComments (11)


Subscribe via email

Receive notifications of new posts by email.

The Arduino Book

Arduino Workshop

Für unsere deutschen Freunde

Dla naszych polskich przyjaciół ...

Australian Electronics!

Buy and support Silicon Chip - Australia's only Electronics Magazine.

Use of our content…

%d bloggers like this: