Tag Archive | "dfrobot"

Tutorial: Arduino and Infra-red control

Learn how to use Arduino and infra-red remote controls in chapter thirty-two of a series originally titled “Getting Started/Moving Forward with Arduino!” by John Boxall – A tutorial on the Arduino universe. The first chapter is here, the complete series is detailed here.

Updated 10/07/2013

In this article we will look at something different to the usual, and hopefully very interesting and useful – interfacing our Arduino systems with infra-red receivers. Why would we want to do this? To have another method to control our Ardiuno-based systems, using simple infra-red remote controls.

A goal of this article is to make things as easy as possible, so we will not look into the base detail of how things work – instead we will examine how to get things done. If you would like a full explanation of infra-red, perhaps see the page on Wikipedia. The remote controls you use for televisions and so on transmit infra-red beam which is turned on and off at a very high speed – usually 38 kHz, to create bits of serial data which are then interpreted by the receiving unit. As the wavelength of infra-red light is too high for human eyes, we cannot see it. However using a digital camera – we can. Here is a demonstration video of IR codes being sent via a particularly fun kit – the adafruit TV-B-Gone:

Now to get started. You will need a remote control, and a matching IR receiver device. The hardware and library used in this tutorial only  supports NEC, Sony SIRC, Philips RC5, Philips RC6, and raw IR protocols. Or you can purchase a matching set for a good price, such as this example:

irpackage

Or you may already have a spare remote laying around somewhere. I kept this example from my old Sony Trinitron CRT TV after it passed away:

sonyremote1

It will more than suffice for a test remote. Now for a receiver – if you have purchased the remote/receiver set, you have a nice unit that is ready to be wired into your Arduino, and also a great remote that is compact and easy to carry about. To connect your receiver module – as per the PCB labels, connect Vcc to Arduino 5V, GND to Arduino GND, and D (the data line) to Arduino digital pin 11.

Our examples use pin 11, however you can alter that later on. If you are using your own remote control, you will just need a receiver module. These are very cheap, and an ideal unit is the Vishay TSOP4138 (data sheet .pdf). These are available from element-14 and the other usual retail suspects. They are also dead-simple to use. Looking at the following example:

From left to right the pins are data, GND and Vcc (to Arduino +5V). So it can be easily wired into a small breadboard for testing purposes. Once you have your remote and receiver module connected, you need to take care of the software side of things. There is a new library to download and install, download it from here. Please note that library doesn’t work for Arduino Leonardo, Freetronics Leostick, etc with ATmega32U4. Instead, use this library (and skip the modification steps below). Extract the IRremote folder and place into the ..\arduinoxxx\libraries folder. Then restart your Arduino IDE if it was already open.

Using Arduino IDE v1.0 or greater? Open the file “IRRemoteInt.h” in the library folder, and change the line

Then save and close the file, restart the Arduino IDE and you’re set.

With our first example, we will receive the commands from our remote control and display them on the serial monitor:

Open the serial monitor box, point your remote control to the receiver and start pressing away. You should see something like this:

What have we here? Lots of hexadecimal numbers. Did you notice that each button on your remote control resulted in an individual hexadecimal number? I hope so. The number FFFFFFFF means that the button was held down. The remote used was from a yum-cha discount TV. Now I will try again with the Sony remote:

This time, each button press resulted in the same code three times. This is peculiar to Sony IR systems. However nothing to worry about. Looking back at the sketch for example 32.1, the

section is critical – if a code has been received, the code within the if statement is executed. The hexadecimal code is stored in the variable

with which we can treat as any normal hexadecimal number. At this point, press a few buttons on your remote control, and take a note of the matching hexadecimal codes that relate to each button. We will need these codes for the next example…

Now we know how to convert the infra-red magic into numbers, we can create sketches to have our Arduino act on particular commands. As the IR library returns hexadecimal numbers, we can use simple decision functions to take action. In the following example, we use switch…case to examine each inbound code, then execute a function. In this case we have an LCD module connected via I2C, and the sketch is programmed to understand fifteen Sony IR codes. If you don’t have an LCD you could always send the output to the serial monitor. If you are using the DFRobot I2C LCD display, you need to use Arduino v23.

Furthermore you can substitute your own values if not using Sony remote controls. Finally, this sketch has a short loop after the translateIR(); function call which ignores the following two codes – we do this as Sony remotes send the same code three times. Again. you can remove this if necessary. Note that when using hexadecimal numbers in our sketch we preced them with 0x:

And here it is in action:


You might be thinking “why would I want to make things appear on the LCD like that?”. The purpose of the example is to show how to react to various IR commands. You can replace the LCD display functions with other functions of your choosing.

At the start working with infra-red may have seemed to be complex, but with the previous two examples it should be quite simple by now. So there you have it, another useful way to control our Arduino systems. Hopefully you have some ideas on how to make use of this technology. In future articles we will examine creating and sending IR codes from our Arduino. Furthermore, a big thanks to Ken Shirriff for his Arduino library.

LEDborder

Have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, control, DFR0107, dfrobot, education, infrared, IR, learning electronics, lesson, microcontrollers, remote, tronixstuff, tutorialComments (17)

The DFRobot LCD4884 LCD Shield

Learn how to use the DFRobot LCD4884 Arduino LCD shield.

Updated 19/03/2013

This needs to be updated for use with Arduino IDE v1.0.1 and greater… however we no longer have a shield to test it. Stay tuned via twitter to find out when this is updated.

This article is my response to a request on how to use the LCD4884 LCD shield from DFRobot in China. It is a simple way of displaying text and the odd graphic, as well as another way to accept user input. Here is the shield in question:

image

From a hardware perspective the LCD has a resolution of 84 by 48 pixels, with a blue back light. It can easily display six rows of fourteen alphanumeric characters, or two rows of six very large characters. Furthermore, it can display bitmap images that are appropriately sized. At the top-left of the shield digital pins eight to thirteen have been expanded with matching Vcc and GND pins, and at the bottom right the same has been done with analogue pins one through to five. Therefore if using this shield, you will lose digital pins two through to seven and analogue zero.

Along the bottom-left of the shield are solder pads for some other I/O options, however I couldn’t find any documentation on how these are used. Below the LCD is a small four-way joystick that also has an integral button. This is connected to analog pin zero via a resistor network. This joystick can be used for user input and also to create some nifty menu systems. To the right is a power-on LED which is really too bright, I would recommend sanding it a little to reduce the intensity, or just melting it off with a soldering iron.

The shield requires an Arduino library which can be downloaded from the shield’s wiki page. There is also a good demonstration sketch on the wiki, however some of our readers may find this to be somewhat complex. Therefore where possible I will break down and explain the functions in order to simplify use of the shield, then use them in a demonstration sketch.

Controlling the backlight is very easy, just use:

digitalWrite(7, HIGH/LOW)

to turn it on and off. Don’t forget to put

pinMode(7, OUTPUT) in void setup();.

Reading the joystick position is accomplished via analogRead(0);. It returns the following values as such:

  • Up – 505
  • Down – 0
  • Left – 740
  • Right – 330
  • pressed in – 144
  • Idle (no action) – 1023

By using analogRead(0) and if… statements you can read the joystick in a simple way. Don’t forget to allow for some tolerance in the readings. Attempts to press the button while forcing a direction did not return any different values. In the example sketch later on, you can see how this is implemented. Always remember to insert:

in void setup() to create an instance of the LCD, and

at the start of your sketch to enable the library.

Now to display text on the LCD. Here is an example of the standard font text:

charactersss

Using the standard font, we can position text using the following function:

The parameter x is for the x-coordinate of the first character – measured in pixels, not characters. However y is the coordinate in character lines (!). The screen can display six lines of fourteen characters. To display the larger font, for example:

largechar

use the following:

Unfortunately the library only supports the digits 0~9, +, – and decimal point. You can modify the file font_big.h in the library folder and create your own characters. Once again the x parameter is the number of pixels across to place the first character, and y is 0 for the top line and 3 for the bottom line. Notice that the characters in this font are proportional, however the maximum number of digits to plan for in one line would be six.

To clear the display, use:

By now you will be able to display text, control the backlight and read the joystick. The following demonstration sketch puts it all together so far:

Next is to create and display bitmap images. Images can be up to 84 x 48 pixels in size. There are no shades of grey in the images, just pixels on or off. To display a bitmap is a convoluted process but can be mastered. We need to convert a bitmap image into hexadecimal numbers which are then stored in a text file for inclusion into the sketch. To do so, follow these steps:

Create your monochrome image using an editor such as Gimp. Make sure your file name ends with .bmp. Such as:

gimpexample

Next, download the BMP2ASM program from this website. [Sorry, could only find a Windows version]. Open your .bmp file as created above, and you will see a whole bunch of hexadecimal numbers at the bottom of the window:

convexam

Turn on the check boxes labelled “Stretch”, “Use Prefix” and “Use suffix”. Then click “Convert”. Have a look in your folder and you will find a text file with an extension .asm. Open this file in a text editor such as Notepad. Remove all the instances of “dt”, as well as the top line with the file path and name. Finally, put commas at the end of each line.

You should now be left with a file of hexadecimal numbers. Encase these numbers in the form of an array as such:

encase

What we have done is places the hexadecimal numbers inside the

declaration. To make life simpler, ensure the filename (ending with .h) is the same as the variable name, as in this example it is called hellobmp(.h). And make sure you have saved this file in the same folder as the sketch that will use it. Finally, we include the hellobmp.h file in our example sketch to display the image:

Notice in the function lcd.LCD_draw_bmp_pixel the filename hellobmp is the same as in the #include declaration is the same as the hellobmp.h file we created. They all need to match. Furthermore, the four numerical parameters are the bitmap’s top-left x-y and bottom-right x-y coordinates on the LCD. So after all that, here is the result:

hellodone

So there you have it. If you have any questions about this LCD shield contact DF Studio, or ask a question in our Google Group.

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, DFR0092, dfrobot, education, LCD, LCD4884, lesson, review, tutorialComments (19)

Kit review: Freetronics 16×2 LCD Arduino Shield

Hello everyone

This kit has now been discontinued, however Freetronics now have a great LCD+Keypad Shield.

Today we examine their latest kit, the “16×2 LCD Arduino Shield“. This is a very easy to construct, yet useful tool for those experimenting, prototyping and generally making things with their Arduino-based systems.  The purpose of the shield is to offer easy access to a 16 x 2 character LCD module, and also the use of five buttons – connected to an analog input using the resistor ladder method. The kit comes packaged very well, and includes not only detailed printed instructions in colour, but also the full circuit schematic:

contentsss

It is nice to see such a high level of documentation, even though most people may not need it – there is generally someone who does. Sparkfun – get the hint. All the parts are included, and for the first time in my life the resistors were labelled as well:

partsss1

So being Mr Pedantic I followed the instructions, and happily had the components in without any troubles. The next step was the Arduino shield pins – the best way to solder these is to insert into your Arduino board, drop the shield on top then solder away as such:

shieldpinsss

And finally, bolting on the LCD whilst keeping the header pins for the LCD in line. Some people may find the bolt closest to D0 interferes with the shield pin, so you can insert the bolt upside down as I have. Remember to not solder the LCD pins until you are happy it is seated in correctly:

lcdtopcbss

Once you are satisfied the pins are lined up and sitting in their required position – solder them in, tighten your nuts and that’s it:

finishedss

The contrast of the LCD in real life is better than shown in the photo above – photographing them is a little difficult for me. However once assembled, using the shield is quite easy. If your LCD doesn’t seem to be working after your first sketch, adjust the contrast using the potentiometer. The LCD is a standard HD44780-interface model, and wired in to use a 4-bit parallel data interface. If using these types of LCD is new to you, perhaps visit this article then return. Our shield uses the pins: A0 and D4~D9.

One uses the standard Arduino liquidCrystal library with this LCD, and the function parameters to use are as follows:

The buttons are read using analog pin A0. Use the following sketch to find the values returned by the analogRead function:

and a quick video of this in action:

Now that we know the values returned for each button, we can take advantage of them to create, for example, a type of menu system – or some sort of controller. In the second example, we have used a modified TwentyTen with a DS1307 real-time clock IC to make a digital clock. The buttons on the LCD shield are utilised to create a user-friendly menu to set the clock time.

You can download the demonstration sketch from here.

In general this is an excellent kit, and considering the price of doing it yourself – good value as well. To get your hands on this product in kit or assembled form – visit Freetronics’ website, or your local reseller.

Remember, if you have any questions about these modules please contact Freetronics via their website. Higher resolution images available on flickr.

[Note – the kit assembled in this article was received from Freetronics for review purposes]

Posted in arduino, kit review, LCDComments (6)


Subscribe via email

Receive notifications of new posts by email.

The Arduino Book

Arduino Workshop

Für unsere deutschen Freunde

Dla naszych polskich przyjaciół ...

Australian Electronics!

Buy and support Silicon Chip - Australia's only Electronics Magazine.

Use of our content…

%d bloggers like this: