Tag Archive | "eeprom"

Discovering Arduino’s internal EEPROM lifespan

How long does the internal EEPROM of an Atmel ATmega328 last for? Let’s find out…

Updated 18/03/2013

Some time ago I published a short tutorial concerning the use of the internal EEPROM  belonging to the Atmel ATmega328 (etc.) microcontroller in our various Arduino boards. Although making use of the EEPROM is certainly useful, it has a theoretical finite lifespan – according to the Atmel data sheet (download .pdf) it is 100,000 write/erase cycles.

One of my twitter followers asked me “is that 100,000 uses per address, or the entire EEPROM?” – a very good question. So in the name of wanton destruction I have devised a simple way to answer the question of EEPROM lifespan. Inspired by the Dangerous Prototypes’ Flash Destroyer, we will write the number 170 (10101010 in binary) to each EEPROM address, then read each EEPROM address to check the stored number. The process is then repeated by writing the number 85 (01010101 in binary) to each address and then checking it again. The two binary numbers were chosen to ensure each bit in an address has an equal number of state changes.

After both of the processes listed above has completed, then the whole lot repeats. The process is halted when an incorrectly stored number is read from the EEPROM – the first failure. At this point the number of cycles, start and end time data are shown on the LCD.

In this example one cycle is 1024 sequential writes then reads. One would consider the entire EEPROM to be unusable after one false read, as it would be almost impossible to keep track of  individual damaged EEPROM addresses. (Then again, a sketch could run a write/read check before attempting to allocate data to the EEPROM…)

If for some reason you would like to run this process yourself, please do not do so using an Arduino Mega, or another board that has a fixed microcontroller. (Unless for some reason you are the paranoid type and need to delete some data permanently). Once again, please note that the purpose of this sketch is to basically destroy your Arduino’s EEPROM. Here is the sketch:

If you are unfamiliar with the time-keeping section, please see part one of my Arduino+I2C tutorial. The LCD used was my quickie LCD shield – more information about that here. Or you could always just send the data to the serial monitor box – however you would need to leave the PC on for a loooooong time… So instead the example sat on top of an AC adaptor (wall wart) behind a couch (sofa)  for a couple of months:

The only catch with running it from AC was the risk of possible power outages. We had one planned outage when our house PV system was installed, so I took a count reading before the mains was turned off, and corrected the sketch before starting it up again after the power cut. Nevertheless, here is a short video – showing the start and the final results of the test:


So there we have it, 1230163 cycles with each cycle writing and reading each individual EEPROM address. If repeating this odd experiment, your result will vary.

Well I hope someone out there found this interesting. Please refrain from sending emails or comments criticising the waste of a microcontroller – this was a one off.

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, atmega328, atmel, EEPROM, hardware hacking, lesson, microcontrollers, projects, tutorialComments (5)

Tutorial: Your Arduino’s inbuilt EEPROM

This is chapter thirty-one of a series originally titled “Getting Started/Moving Forward with Arduino!” by John Boxall – A tutorial on the Arduino universe. The first chapter is here, the complete series is detailed here 

[Updated 09/01/2013]

Today we are going to examine the internal EEPROM in our Arduino boards. What is an EEPROM some of you may be saying? An EEPROM is an Electrically Erasable Programmable Read-Only Memory. It is a form of non-volatile memory that can remember things with the power being turned off, or after resetting the Arduino. The beauty of this kind of memory is that we can store data generated within a sketch on a more permanent basis.

Why would you use the internal EEPROM? For situations where data that is unique to a situation needs a more permanent home. For example, storing the unique serial number and manufacturing date of a commercial Arduino-based project – a function of the sketch could display the serial number on an LCD, or the data could be read by uploading a ‘service sketch’. Or you may need to count certain events and not allow the user to reset them – such as an odometer or operation cycle-counter.

What sort of data can be stored? Anything that can be represented as bytes of data. One byte of data is made up of eight bits of data. A bit can be either on (value 1) or off (value 0), and are perfect for representing numbers in binary form. In other words, a binary number can only uses zeros and ones to represent a value. Thus binary is also known as “base-2″, as it can only use two digits.

How can a binary number with only the use of two digits represent a larger number? It uses a lot of ones and zeros. Let’s examine a binary number, say 10101010. As this is a base-2 number, each digit represents 2 to the power of x, from x=0 onwards:

binary2 binary12

See how each digit of the binary number can represent a base-10 number. So the binary number above represents 85 in base-10 – the value 85 is the sum of the base-10 values. Another example – 11111111 in binary equals 255 in base 10.

binary2

Now each digit in that binary number uses one ‘bit’ of memory, and eight bits make a byte. Due to internal limitations of the microcontrollers in our Arduino boards, we can only store 8-bit numbers (one byte) in the EEPROM. This limits the decimal value of the number to fall between zero and 255. It is then up to you to decide how your data can be represented with that number range. Don’t let that put you off – numbers arranged in the correct way can represent almost anything!

There is one limitation to take heed of – the number of times we can read or write to the EEPROM. According to the manufacturer Atmel, the EEPROM is good for 100,000 read/write cycles (see the data sheet). One would suspect this to be a conservative estimate, however you should plan accordingly. *Update* After some experimentation, the life proved to be a lot longer

Now we know our bits and and bytes, how many bytes can be store in our Arduino’s microcontroller? The answer varies depending on the model of microcontroller. For example:

  • Boards with an Atmel ATmega328, such as Arduino Uno, Uno SMD, Lilypad or the Freetronics KitTen/Eleven – 1024 bytes (1 kilobyte)
  • Boards with an Atmel ATmega1280 or 2560, such as the Arduino Mega series – 4096 bytes (4 kilobytes)
  • Boards with an Atmel ATmega168, such as the original Arduino Lilypad, old Nano, Diecimila etc – 512 bytes.

If y0u are unsure have a look at the Arduino hardware index or ask your board supplier.

If you need more EEPROM storage than what is available with your microcontroller, consider using an external I2C EEPROM as described in the Arduino and I2C tutorial part two.

At this point we now understand what sort of data and how much can be stored in our Arduino’s EEPROM. Now it is time to put this into action. As discussed earlier, there is a finite amount of space for our data. In the following examples, we will use a typical Arduino board with the ATmega328 with 1024 bytes of EEPROM storage.

To use the EEPROM, a library is required, so use the following library in your sketches:

The rest is very simple. To store a piece of data, we use the following function:

The parameter a is the position in the EEPROM to store the integer (0~255) of data b. In this example, we have 1024 bytes of memory storage, so the value of a is between 0 and 1023. To retrieve a piece of data is equally as simple, use:

Where z is an integer to store the data from the EEPROM position a. Now to see an example.

This sketch will create random numbers between 0 and 255, store them in the EEPROM, then retrieve and display them on the serial monitor. The variable EEsize is the upper limit of your EEPROM size, so (for example) this would be 1024 for an Arduino Uno, or 4096 for a Mega.

The output from the serial monitor will appear as such:

So there you have it, another useful way to store data with our Arduino systems. Although not the most exciting tutorial, it is certainly a useful.

LEDborder

Have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, education, EEPROM, lesson, microcontrollers, tutorialComments (33)

Tutorial: Arduino and the I2C bus – Part Two

Part two of our Arduino and I2C bus tutorial.

[Updated 28/11/2014]

Today we are going to continue learning about the I2C bus and how it can work for us. If you have not already, please read and understand the first I2C article before continuing.

First of all, there are some limitations of I2C to take into account when designing your projects. One of these is the physical length of the SDA and SCL lines. If all your devices are on the same PCB, then there is nothing to worry about, however if your I2C bus is longer than around one metre, it is recommended that you use an I2C bus extender IC. These ICs reduce electrical noise over the extended-length bus runs and buffer the I2C signals to reduce signal degradation and chance of errors in the data. An example of such an IC is the NXP P82B715 (data sheet). Using a pair of these ICs, you can have cable runs of 20 to 30 metres, using shielded twisted-pair cable. Below is a good example of this, from the aforementioned NXP data sheet:

i2cbufferedss

Several applications come to mind with an extended I2C bus, for example remote temperature monitoring using the the ST Microelectronics CN75 temperature sensor from part one; or controlling several I/O ports using an I2C expander without the expense or worry of using a wireless system. Speaking of which, let’s do that now…

A very useful and inexpensive part is the PCF8574 I/O expander (data sheet.pdf). This gives us another eight outputs, in a very similar method to the 74HC595; or can be used as eight extra inputs. In fact, if you were to use more than one 74HC595 this IC might be preferable, as you can individually address each chip instead of having to readdress every IC in line as you would with shift registers. So how do we do this? First, let’s consult the pinout:

There should not be any surprises for you there. A2~A0 are used to select the last three bits of the device address, P0~P7 are the I/O pins, and INT is an interrupt output which we will not use. To address the PCF8574 we need two things, the device address, and a byte of data which represents the required output pin state. Huh? Consider:

pcf8574intdef

So if we set pins A0 to A2 to GND, our device address in binary will be 0100000, or 0x20 in hexadecimal. And the same again to set the output pins, for example to turn them all on we send binary 0 in hexadecimal which is 0; or to have the first four on and the second four off, use 00001111 which is Ox0F. Hopefully you noticed that those last two values seemed backwards – why would we send a zero to turn all the pins on?

The reason is that the PCF8574 is a current sink. This means that current runs from +5v, through into the I/O pins. For example, an LED would have the anode on the +5V, and the cathode connected to an I/O pin. Normally (for example with a 74HC595) current would run from the IC, through the resistor, LED and then to earth. That is a current source. Consider the following quick diagram:

sinksource1

In the example above, please note that the PCF8574N can take care of current limitation with LEDs, whereas the 74HC595 needs a current-limiting resistor to protect the LED.

Luckily this IC can handle higher volumes of current, so a resistor will not be required. It sounds a bit odd, but like anything is easy once you spend a few moments looking into it. So now let’s use three PCF8574s to control 24 LEDs. To recreate this masterpiece of blinkiness you will need:

  • Arduino Uno or compatible board
  • A large solderless breadboard
  • Three PCF8574 I/O extenders
  • Eight each of red, green and yellow (or your choice) LEDs, each with a current draw of no more than 20mA
  • Two 4.7 kilo ohm resistors
  • Hook-up wires
  • Three 0.1 uF ceramic capacitors

Here is the schematic:

exam21p1schemss

… and the example board layout:

example21p1boardss

and the example sketch. Note that the device addresses in the sketch match the schematic above. If for some reason you are wiring your PCF8574s differently, you will need to recalculate your device addresses:

 And finally our demonstration video:


That was a good example of controlling many outputs with our humble I2C bus. You could literally control hundreds of outputs if necessary – a quite inexpensive way of doing so. Don’t forget to take into account the total current draw of any extended circuits if you are powering from your Arduino boards.

LEDborder

The next devices to examine on our I2C bus ride are EEPROMs – Electrically Erasable Programmable Read-Only Memory. These are memory chips that can store data without requiring power to retain memory. Why would we want to use these? Sometimes you might need to store a lot of reference data for use in calculations during a sketch, such as a mathematical table; or perhaps numerical representations of maps or location data; or create your own interpreter within a sketch that takes instruction from data stored in an array.

In other words, an EEPROM can be used to store data of a more permanent use, ideal for when your main microcontroller doesn’t haven enough memory for you to store the data in the program code. However, EEPROMs are not really designed for random-access or constant read/write operations – they have a finite lifespan. But their use is quite simple, so we can take advantage of them.

EEPROMS, like anything else come in many shapes and sizes. The model we will examine today is the Microchip 24LC256 (data sheet.pdf). It can hold 256 kilobits of data (that’s 32 kilobytes) and is quite inexpensive. This model also has selectable device addresses using three pins, so we can use up to eight at once on the same bus. An example:

24lc256bb

The pinouts are very simple:

Pin 7 is “write protect” – set this low for read/write or high for read only. You could also control this in software if necessary. Once again we need to create a slave I2C device address using pins 1, 2 and 3 – these correlate to A2, A1 and A0 in the following table:

So if you were just using one 24LC256, the easiest solution would be to set A0~A2 to GND – which makes your slave address 1010000 or 0x50 in hexadecimal. There are several things to understand when it comes to reading and writing our bytes of data. As this IC has 32 kilobytes of storage, we need to be able to reference each byte in order to read or write to it. There is a slight catch in that you need more than one byte to reference 32767 (as in binary 32767 is 11111111 0100100 [16 bits]).

So when it comes time to send read and write requests, we need to send two bytes down the bus – one representing the higher end of the address (the first 8 bits from left to right), and the next one representing the lower end of the address (the final 8 bits from left to right) – see figure 6.1 on page 9 of the data sheet.

An example – we need to reference byte number 25000. In binary, 25000 is 0110000110101000. So we split that up into 01100001 and 10101000, then covert the binary values to numerical bytes with which to send using the Wire.send(). Thankfully there are two operators to help us with this. This first is >>, known as bitshift right. This will take the higher end of the byte and drop off the lower end, leaving us with the first 8 bits. To isolate the lower end of the address, we use another operator &, known as bitwise and. This unassuming character, when used with 0XFF can separate the lower bits for us. This may seem odd, but will work in the examples below.

Writing data to the 24LC256

Writing data is quite easy. But first remember that a byte of data is 11111111 in binary, or 255 in decimal. First we wake up the I2C bus with:

then send down some data. The first data are the two bytes representing the address (25000) of the byte (12) we want to write to the memory.

And finally, we send the byte of data to store at address 25000, then finish the connection:

There we have it. Now for getting it back…

Reading data from the 24LC256

Reading is quite similar. First we need to start things up and move the pointer to the data we want to read:

Then, ask for the byte(s) of data starting at the current address:

In this example, incomingbyte is a byte variable used to store the data we retrieved from the IC. Now we have the theory, let’s put it into practice with the test circuit below, which contains two 24LC256 EEPROMs. To recreate this you will need:

  • Arduino Uno or compatible board
  • A large solderless breadboard
  • Two Microchip 24LC256 EEPROMs (you can use 24LC512s as well)
  • Two 4.7 kilo ohm resistors
  • Hook-up wires
  • Two 0.1 uF ceramic capacitors

Here is the schematic:

examp21p2schemss

… the board layout:

exam21p2boardss

and the example sketch. Note that the device addresses in the sketch match the schematic above. If for some reason you are wiring your 24LC256s differently, you will need to recalculate your device addresses. To save time with future coding, we have our own functions for reading and writing bytes to the EEPROM – readData() and writeData(). Consider the sketch for our example:

And the output from the example sketch:

example21p2result

Although the sketch in itself was simple, you now have the functions to read and write byte data to EEPROMS. Now it is up to your imagination to take use of the extra memory.

If you enjoyed this article, or want to introduce someone else to the interesting world of Arduino – check out my book (now in a fourth printing!) “Arduino Workshop”.

visit tronixlabs.com

Have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our forum – dedicated to the projects and related items on this website.

Posted in 24LC256, arduino, I2C, learning electronics, lesson, microcontrollers, PCF8574, tutorialComments (17)


Subscribe via email

Receive notifications of new posts by email.

The Arduino Book

Arduino Workshop

Für unsere deutschen Freunde

Dla naszych polskich przyjaciół ...

Australian Electronics!

Buy and support Silicon Chip - Australia's only Electronics Magazine.

Use of our content…

%d bloggers like this: