Tag Archive | "equipment"

Kit review – High Accuracy LC Meter

Hello readers

Time for another kit review. Lately one of my goals has been to make life easier and in doing so having some decent test equipment. One challenge of meeting that goal is (naturally) keeping the cost of things down to a reasonable level. Unfortunately my eyesight is not the best so I cannot read small capacitor markings – which makes a capacitance meter necessary. Although I have that function within my multimeter, it is often required to read resistors in the same work session.

Thus the reason for this kit review – the High Precision LC Meter kit. The details were originally published in the May 2008 issue of Australia’s Silicon Chip magazine. The meter specifications are:

  • Capacitance – 0.1pF to over 800 nF with four-digit resolution;
  • Inductance – 10 nH to over 70 mH with four-digit resolution;
  • Accuracy of better than +/- 1% of the reading;
  • Automatic range selection, however only non-polarised capacitors can be measured.

The power drain is quite low,  between 8 (measurement) and 17 milliamps (calibration). Using a fresh 9V alkaline battery you should realise around fifty to sixty hours of continuous use. At this point some of you may be wondering if it is cheaper to purchase an LC meter or make your own. A quick search found the BK Precision 875B LCR meter with the same C range and a worse L range for over twice the price of the kit. Although we don’t have resistance measurement in our kit, if you are building this you already have a multimeter. So not bad value at all. And you can say you built it 🙂

Speaking of building, assembly time was just under two hours, and the kit itself is very well produced. The packaging was the typical retail bag:

retailkitss

The first thing that grabs your attention is the housing. It is a genuine, made in the US Hammond enclosure – and has all the required holes and LCD area punched out, so you don’t need to do any drilling at all:

hammondcasess

The enclosure has nice non-slip rubberised edging (the grey area) and also allows for a 9V battery to be housed securely. The team at Altronics have done a great job in redesigning the kit for this enclosure, much more attractive than the magazine version. The PCB is solder-masked and silk-screened to fine standard:

pcbss2

There are two small boards to cut and file off from the main PCB. We will examine them later in the article. All required parts for completion were included, and it is good to see 1% resistors and an IC socket for the microcontroller:

partsss1

At first I was a little disappointed to not have a backlit LCD module, however considering the meter is to be battery operated (however there is a DC socket for a plugpack) and you wouldn’t really be using this in the dark, a backlight wouldn’t be necessary. Construction was easy enough, the layout on the PCB is well labelled, and plenty of space between pins. Lately I have started using a lead-former, and can highly recommend the use of one:

leadformerss

Assembly was quite simple, just start with the lower profile components:

assemble1ss

 

… then mount the LCD and the larger components:

assemble2ss

… the switches and others – and we’re done:

finishedsolderingss

The only problem at this point was the PCB holes for the selector switch, one hole was around 1mm from where it needed to be. Instead of drilling out the hole, it was easier to just bend up the legs of the switch and keep going:

switchlegsss

At this stage one has to cut out two supports from the enclosure, which can be done easily. Then insert the PCB and solder to the sockets and power (9V battery snap). Initial testing was successful (after adjusting the LCD contrast…

inittestss

If you look at the area of PCB between the battery and the left-hand screw there are eight pins – these are four pairs of inputs used to help calibrate and check operation of the meter. For example, by placing a jumper over a pair you can display the oscillator frequency at various stages:

calibrationss

Furthermore, those links can also be used to fine-tune the meter. For example one can increase or decrease the scaling factor and the settings are then stored in the EEPROM within the microcontroller. However my example seemed ok from the start, so it was time to seal up the enclosure and get testing. Starting with a ceramic capacitor, the lowest value in stock:

3p9pfss

Spot-on. That was a good start, however trying to bend the leads to match the binding posts was somewhat inconvenient, so I cut up some leads and fitted crocodile clips on the end. The meter’s zero button allows you to reset the measurement back to zero after attaching the leads, so stray capacitance can be taken into account.

Next, time to check the measurement with something more accurate, a 1% tolerance silvered-mica 100 picofarad capacitor:

99pfss

Again, the meter came through right on specification. My apologies to those looking for inductor tests – I don’t have any in stock to try out. If you are really curious I could be persuaded to order some in, however as the capacitance measurement has been successful I am confident the inductance measurement would also fall within the meter’s specifications.

As shown earlier, there were two smaller PCBs included:

pcbadaptorsss

The top PCB is a shorting bar used to help zero the inductance reading, and the lower PCB is used to help measure smaller capacitors and also SMD units. A nice finishing touch that adds value to the meter. The only optional extra to consider would be a set of short leads with clips or probes to make measurement physically easier.

When reading this kit review it may appear to be somewhat positive and not critical at all. However it really is a  good instrument, considering the accuracy, price, and enjoyment from doing it yourself. It was interesting, easy to build, and will be very useful now and in the future. So if you are in the market for an LC meter, and don’t mind some work – you should add this kit to your checklist for consideration. It is available from our store – Tronixlabs.com

 

visit tronixlabs.com

… which along with being Australia’s #1 Adafruit distributor, also offers a growing range and Australia’s best value for supported hobbyist electronics from DFRobot, Freetronics, Seeedstudio and much much more.

As always, have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our forum – dedicated to the projects and related items on this website.

Posted in K2533, kit review, LC meter, test equipment, tronixlabsComments (18)

Review – Fluke 233 Remote Display True RMS Multimeter

Hello readers

Several followers of my website have noticed the use of an interesting multimeter in a few of my articles, and were curious about it. So in this article we will discuss it in more detail. It is certainly novel in design, and has proven to be very convenient in use – the Fluke 233 remote-display true RMS multimeter. It arrives in a cardboard box that is easily recycled:

boxs

Upon tearing open the packaging we are presented with the following contents:

contentss

The contents of the box are as follows:

  • The meter itself;
  • a long (~1.2m) pair of Cat IV leads with very sharp points;
  • matching insulated alligator clip adaptors;
  • a K-type thermocouple;
  • a printed Getting Started manual, and the complete manual on CDROM;
  • a single, universal getting started sheet – explains how to remove battery isolation tabs.

However, a carry case was not included. Considering the cost of the meter here (Au$550 + tax), one would have expected a case. On the other hand, if you/your workplace can afford a 233, you can pay for your own case. So there’s two angles to the case perspective.

It is good to see that there isn’t too much of a printer manual, the less paper used the better. As others have said, if you have one of these meters the manual isn’t necessary apart from checking the specifications, and the same applied to myself. Thoughtfully the meter is supplied and fitted with 5 x AA Duracell alkaline cells, three in the meter body and two in the display unit. All one needs to do is pull out the plastic tabs from the battery compartments, and you’re ready to go.

Physically the unit does not disappoint. Made in the USA. First class. Another solid Fluke design, clean lines, and a great fit and finish. Futhermore it is of a good weight, so you could always bang in a nail with it, or the pointy-head boss. The exterior has the rubber-moulded housing which is not removable, however this would be recommended for the target market – as the 233 would be more of a field work than a test-bench instrument. However, if you do sit it on the bench with the tilting bail, you can still operate it with one hand as it has enough friction to stay put. It is also good to see that the box and packaging are cardboard which is easily recycled.

After flicking the meter on the first thing to do was remove the display, plug in the thermocouple, and toss the body into the freezer:

freezer-tests

Even with the meter in the freezer, I could still move the display around 1.5 meters away and it still received the data signal. Notice how the display is on the freezer door – it is magnetic. Immediately the benefits of the remote display come to mind. You can always have the display right where you want it, and the meter where it needs to be… it’s win-win. After showing it to my auto-electrician friend, she didn’t want to give it back.

The ability to set up a meter in a less than perfectly safe environment and take the display away is almost priceless. Furthermore, the backlight is a nice even blueish colour, and times out after around forty seconds. Whilst in the kitchen, I tested out the external temperature of my tea:

teas

Using the meter in general is very simple, you can hold it in one hand and select all of the functions with your thumb. Having the yellow shift key makes changing between associated readings very simple, for example after reading AC voltage:

241vacs

Then pressing the shift key changes to frequency:

50-hzss

The meter has several useful indication functions – while working with high voltages the triangular market is illuminated; when changing to temperature you are prompted with “OPEN” for the thermocouple, and changing to current you are prompted with “LEAD” to change sockets. It is obvious after a short period of time this was designed by engineers for engineers, and not made to a ‘price’. Although this is not an electronics multimeter, it still has quite a few ranges that would suit at a pinch. Plus the one-touch data hold, minimum and maximum functions are included as with other top-end Flukes. Hopefully someone at Fluke is working on a remote display version of their 87V.

Now that I have had this meter for just over five months, it has already become a worthwhile addition to my bench. For the kind of work I do, it has already replaced another multimeter, my old frequency counter and thermometer. The ranges are quite useful, and the continuity beeper is in the display not the body. According to the manual the 233 is rated for a one meter drop onto any of the six surfaces. Out of respect to the meter I will not throw it into a river or from a moving car. The other factor that prevents me from going to such extremes is the clear plastic over the LCD – there is a small amount of ‘give’ or flexibility in that area. Otherwise the 233 is as solid as they come.

The specifications can be found in detail in the manual here, however a quick glance shows:

Range                                                             Accuracy

AC voltage: 0.1mV ~ 1000V                      1~2%+3

AC current: 1mA ~ 10A                               1.5%+3

DC voltage: 0.1mV ~ 1000V                     0.25%+2

DC current: 1mA ~ 10A                               1.0%+3 ** no microamperes

resistance: 0.1 ~ 40 meg-ohm                   0.9~1.5%+2

frequency:  0.01 Hz ~ 50 kHz                    0.1%+2

capacitance: 1nF to 9999 uF                     1.9%+2

temperature: -40 ~ 400 degrees Celsius     1%+10

And there is also a diode test and continuity beeper function. Interestingly enough, I discovered by accident that the frequency counter function was slightly underrated. Some more testing showed it was good for up to 99.48 kHz:

233_freq

Not bad at all. However as with the many pros, there are  a few cons to using this meter. The auto-zero time of the display is a little slow, sometimes it can take two seconds. That doesn’t sound like much, but when you’re measuring many components the time adds up. And the LCD is not protected as well as expected, you can push into it with your finger. For a Fluke meter, one would expect it to be much more solid – if the display unit fell from a height and landed on something pointy with the display facing down, it would be ruined. So be careful if you have one.

Furthermore, the battery life is around eight to ten weeks of “daily use” (perhaps seven hours a week, usually with the backlight on). Some have said this is bad, however my opinion is that the convenience of the remote display makes up for the shorter battery life.

However at the end of the day – this is a great tool. Being able to measure something outside your field of vision, and having the results in front of you is incredibly useful. You could achieve the same functions by using a meter with a PC interface, but that can be overkill and time-consuming to set up. So if the specifications of the 233 meet your needs, this is a great tool that will serve you very well.

The Fluke 233 Remote Display True RMS Multimeter is available from your local element-14 or Fluke distributor.

As always, thank you for reading and I look forward to your comments and so on. Furthermore, don’t be shy in pointing out errors or places that could use improvement. Please subscribe using one of the methods at the top-right of this web page to receive updates on new posts. Or join our Google Group.

[Disclaimer – the Fluke 233 is a review sample made available by Fluke via element-14]

Posted in 233, fluke, learning electronics, product review, test equipmentComments (6)


Subscribe via email

Receive notifications of new posts by email.

The Arduino Book

Arduino Workshop

Für unsere deutschen Freunde

Dla naszych polskich przyjaciół ...

Australian Electronics!

Buy and support Silicon Chip - Australia's only Electronics Magazine.

Use of our content…

%d bloggers like this: