Tag Archive | "how"

Tutorial: Arduino and the MSGEQ7 Spectrum Analyzer

This is a tutorial on using the MSGEQ7 Spectrum Analyser with Arduino, and chapter forty-eight of a series originally titled “Getting Started/Moving Forward with Arduino!” by John Boxall – A tutorial on the Arduino universe. The first chapter is here, the complete series is detailed here.

Updated 30/01/2013

In this article we’re going to explain how to make simple spectrum analysers with an Arduino-style board. (Analyser? Analyzer? Take your pick).

First of all, what is a spectrum analyser? Good question. Do you remember what  this is?

It’s a mixed graphic equaliser/spectrum analyser deck for a hi-fi system. The display in the middle is the spectrum analyser, and roughly-speaking it shows the strength of  different frequencies in the music being listened to – and looked pretty awesome doing it. We can recreate displays similar to this for entertainment and also as a base for creative lighting effects. By working through this tutorial you’ll have the base knowledge to recreate these yourself.

We’ll be using the MSGEQ7 “seven band graphic equaliser IC” from Mixed Signal Integration. Here’s the MSGEQ7 data sheet (.pdf).  This little IC can accept a single audio source, analyse seven frequency bands of the audio, and output a DC representation of each frequency band. This isn’t super-accurate or calibrated in any way, but it works. You can get the IC separately, for example:


and then build your own circuit around it… or like most things in the Arduino world – get a shield. In this case, a derivative of the original Bliptronics shield by Sparkfun. It’s designed to pass through stereo audio via 3.5mm audio sockets and contains two MSGEQ7s, so we can do a stereo analyser:

As usual Sparkfun have saved a few cents by not including the stackable header sockets, so you’ll need to buy and solder those in yourself. There is also space for three header pins for direct audio input (left, right and common), which are useful – so if you can add those as well.

So now you have a shield that’s ready for use. Before moving forward let’s examine how the MSGEQ7 works for us. As mentioned earlier, it analyses seven frequency bands. These are illustrated in the following graph from the data sheet:

freqresponse

It will return the strengths of the audio at seven points – 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz and 16 kHz – and as you can see there is some overlap between the bands. The strength is returned as a DC voltage – which we can then simply measure with the Arduino’s analogue input and create a display of some sort. At this point audio purists, Sheldonites and RF people might get a little cranky, so once again – this is more for visual indication than any sort of calibration device.

However as an 8-pin IC a different approach is required to get the different levels. The IC will sequentially give out the levels for each band on pin 3- e.g. 63 Hz then 160 Hz then 400 Hz then 1 kHz then 2.5 kHz then 6.25 kHz  then 16 kHz then back to 63 Hz and so on. To start this sequence we first reset the IC by pulsing the RESET pin HIGH then low. This tells the IC to start at the first band. Next, we set the STROBE pin to LOW, take the DC reading from pin 3 with analogue input, store the value in a variable (an array), then set the STROBE pin HIGH. We repeat the strobe-measure sequence six more times to get the rest of the data, then RESET the IC and start all over again. For the visual learners consider the diagram below from the data sheet:

strobing1

To demonstrate this process, consider the function

in the following example sketch:

If you follow through the sketch, you can see that it reads both left- and right-channel values from the two MSGEQ7s on the shield, then stores each value in the arrays left[] and right[]. These values are then sent to the serial monitor for display – for example:

If you have a function generator, connect the output to one of the channels and GND – then adjust the frequency and amplitude to see how the values change. The following video clip is a short demonstration of this – we set the generator to 1 kHz and adjust the amplitude of the signal. To make things easier to read we only measure and display the left channel:


Keep an eye on the fourth column of data – this is the analogRead() value returned by the Arduino when reading the 1khz frequency band. You can also see the affect on the other bands around 1 kHz as we increase and decrease the frequency. However that wasn’t really visually appealing – so now we’ll create a small and large graphical version.

First we’ll use an inexpensive LCD, the I2C model from akafugu reviewed previously. To save repeating myself, also review how to create custom LCD characters from here.

With the LCD with have two rows of sixteen characters. The plan is to use the top row for the levels, the left-channel’s on … the left, and the right on the right. Each character will be a little bar graph for the level. The bottom row can be for a label. We don’t have too many pixels to work with, but it’s a compact example:

lcdfullon

We have eight rows for each character, and the results from an analogueRead() fall between 0 and 1023. So that’s 1024 possible values spread over eight sections. Thus each row of pixels in each character will represent 128 “units of analogue read” or around 0.63 V if the Arduino is running from true 5 V (remember your AREF notes?). The sketch will again read the values from the MSGEQ7, feed them into two arrays – then display the required character in each band space  on the LCD.

Here’s the resulting sketch:

If you’ve been reading through my tutorials there isn’t anything new to worry about. And now for the demo, with sound –

That would look great on the side of a Walkman, however it’s a bit small. Let’s scale it up by using a Freetronics Dot Matrix Display – you may recall these from Clock One. For some background knowledge check the review here.  Don’t forget to use a suitable power supply for the DMD – 5 V at 4 A will do nicely. The DMD contains 16 rows of 32 LEDs. This gives us twice the “resolution” to display each band level if desired. The display style is subjective, so for this example we’ll use a single column of LEDs for each frequency band, with a blank column between each one.

We use a lot of line-drawing statements to display the levels, and clear the DMD after each display. With this and the previous sketches, there could be room for efficiency – however I write these with the beginner in mind. Here’s the sketch:

… and here it is in action:

Conclusion

At this point you have the knowledge to use the MSGEQ7 ICs to create some interesting spectrum analysers for entertainment and visual appeal – now you just choose the type of display enjoy the results.

LEDborder

Have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in analyser, analyzer, arduino, BLIPTRONICS, com-10468, dev-10306, education, graphic, lesson, MSGEQ7, sparkfun, spectrum, tutorialComments (34)

Tutorial: Arduino and the NXP SAA1064 4-digit LED display driver

Learn how to use the NXP SAA1064 LED display driver IC in chapter thirty-nine of a series originally titled “Getting Started/Moving Forward with Arduino!” by John Boxall – a series of articles on the Arduino universe.

Updated 19/01/2013

In this article we investigate controlling the NXP (formerly Philips) SAA1064 4-digit LED display driver IC with Arduino and the I2C bus interface. If you are not familiar with using the I2C bus, please read my tutorials (parts one and two) before moving on. Although the SAA1064 is not the newest on the market, it is still popular, quite inexpensive and easy to source. Furthermore as it is controlled over the I2C bus – you don’t waste any digital I/O pins on your Arduino, and you can also operate up to four SAA1064s at once (allowing 16 digits!). Finally, it has a constant-current output – keeping all the segments of your LED display at a constant brightness (which is also adjustable).  So let’s get started…

Here is an example of the SAA1064 in SOIC surface mount packaging:

It measures around 15mm in length. For use in a solderless breadboard, I have soldered the IC onto a through-hole adaptor:

The SAA1064 is also available in a regular through-hole DIP package. At this point, please download the data sheet (.pdf) as you will need to refer to it during the article. Next, our LED display examples. We need common-anode displays, and for this article we use two Agilent HDSP521G two-digit modules (data sheet [.pdf]) as shown below:

For the uninitiated – a common anode display has all the segments’ anodes connected together, with the cathodes terminated separately. For example, our LED displays are wired as such:

Notice the anodes for the left digit are pin 14, and the right digit pin 13. A device that is connected to all the cathodes (e.g. our SAA1064) will control the current flow through each element – thereby turning each segment on (and controlling the brightness) or off. Our SAA1064 is known as a current-sink as the current flows through the LED, and then sinks into the IC.

Now, let’s get it connected. There is an excellent demonstration circuit on page twelve of the data sheet that we will follow for our demonstrations:

It looks pretty straight-forward, and it is. The two transistors are standard NPN-type, such as PN2222. The two transistors are used to each turn on or off a pair of digits – as the IC can only drive digits 1+3 or 2+4 together. (When presented in real life the digits are numbered 4-3-2-1). So the pairs are alternatively turned on and off at a rapid rate, which is controlled by the capacitor between pin 2 and GND. The recommended value is 2.7 nF. At the time of writing, I didn’t have that value in stock, so chose a 3.3 nF instead. However due to the tolerance of the ceramic capacitor it was actually measured to be 2.93 nF:

So close enough to 2.7 nF will be OK. The other capacitor shown between pins 12 and 13 is a standard 0.1 uF smoothing capacitor. Pin 1 on the SAA1064 is used to determine the I2C bus address – for our example we have connected it straight to GND (no resistors at all) resulting in an address of 0x70. See the bottom page five of the data sheet for other address options. Power for the circuit can be taken from your Arduino’s 5V pin – and don’t forget to connect the circuit GND to Arduino GND. You will also use 4.7k ohm pull-up resistors on the SDA and SCL lines of the I2C bus.

The last piece of the schematic puzzle is how to connect the cathodes of the LED displays to the SAA1064. Display pins 14 and 13 are the common anodes of the digits.

The cathodes for the left-hand display module:

  • LED display pins 4, 16, 15, 3, 2, 1, 18 and 17 connect to SAA1064 pins 22, 21, 20, 19, 18, 17, 16 and 15 respectively (that is, LED pin 4 to IC pin 22, etc.);
  • LED display pins 9, 11, 10, 8, 6, 5, 12 and 7 also connect to SAA1064 pins 22, 21, 20, 19, 18, 17, 16 and 15 respectively.
The cathodes for the right-hand display module:
  • LED display pins 4, 16, 15, 3, 2, 1, 18 and 17 connect to SAA1064 pins 3, 4, 5, 6, 7, 8, 9 and 10 respectively;
  • LED display pins  9, 11, 10, 8, 6, 5, 12 and 7 also connect to SAA1064 pins 3, 4, 5, 6, 7, 8, 9 and 10 respectively.
Once your connections have been made, you could end up with spaghetti junction like this…
Now it is time to consider the Arduino sketch to control out SAA1064. Each write request to the SAA1064 requires several bytes. We either send a control command (to alter some of the SAA1064 parameters such as display brightness) or a display command (actually display numbers). For our example sketches the I2C bus address “0x70 >> 1″ is stored in the byte variable saa1064. First of all, let’s look at sending commands, as this is always done first in a sketch to initiate the SAA1064 before sending it data.
As always, we send the address down the I2C bus to awaken the SAA1064 using

Then the next byte is the instruction byte. If we send zero:

… the IC expects the next byte down the bus to be the command byte. And finally our command byte:

The control bits are described on page six of the data sheet. However – for four-digit operation bits 0, 1 and 2 should be 1; bit 3 should be 0; and bits 4~6 determine the amount of current allowed to flow through the LED segments. Note that they are cumulative, so if you set bits 5 and 6 to 1 – 18 mA of current will flow. We will demonstrate this in detail later on.

Next, to send actual numbers to be displayed is slightly different. Note that the digits are numbered (from left to right) 4 3 2 1. Again, we first send the address down the I2C bus to awaken the SAA1064 using

Then the next byte is the instruction byte. If we send 1, the next byte of data will represent digit 1. If that follows with another byte, it will represent digit 2. And so on. So to send data to digit 1, send

Although sending binary helps with the explanation, you can send decimal equivalents. Next, we send a byte for each digit (from right to left). Each bit in the byte represents a single LED element of the digit as well as the decimal point. Note how the elements are labelled (using A~G and DP) in the following image:

The digit bytes describe which digit elements to turn on or off. The bytes are described as such: Bpgfedcba. (p is the decimal point). So if you wanted to display the number 7, you would send B00000111 – as this would turn on elements a, b and c. To add the decimal point with 7 you would send B10000111. You can also send the byte as a decimal number. So to send the digit 7 as a decimal, you would send 7 – as 00000111 in base-10 is 7. To include the decimal point, send 135 – as 100000111 in base-10 is 135. Easy! You can also create other characters such as A~F for hexadecimal. In fact let’s do that now in the following example sketch:

In the function initDisplay() you can see an example of using the instruction then the control byte. In the function clearDisplay() you can see the simplest form of sending digits to the display – we send 0 for each digit to turn off all elements in each digit. The bytes that define the digits 0~9 and A~F are stored in the array digits[]. For example, the digit zero is 63 in decimal, which is B00111111 in binary – which turns on elements a,b,c,d,e and f. Finally, notice the second loop in displayDigits() – 128 is added to each digit value to turn on the decimal point. Before moving on, let’s see it in action:

Our next example revisits the instruction and control byte – we change the brightness of the digits by setting bits 4~6 in the control byte. Each level of brightness is separated into a separate function, and should be self-explanatory. Here is the sketch:

And again, see it in action:

For our final example, there is a function displayInteger(a,b) which can be used to easily display numbers from 0~9999 on the 4-digit display. The parameter a is the number to display, and b is the leading-zero control – zero – off, one – on. The function does some maths on the integet to display and separates the digits for each column, then sends them to the SAA1064 in reverse order. By now you should be able to understand the following sketch:

And the final example in action:

So there you have it – another useful IC that can be used in conjunction with our Arduino systems to make life easier and reduce the required digital output pins.

LEDborder

Have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, education, I2C, LED, lesson, microcontrollers, SAA1064, tutorialComments (27)

Kit Review – Snootlab Mémoire SD card/RTC/prototyping shield

Hello Readers

In this article we will examine another product from a bundle sent for review by Snootlab, a Toulouse, France-based company that in their own words:

… designs and develops electronic products with an Open Hardware and Open Source approach. We are particularly specialized in the design of new shields for Arduino. The products we create are licensed under CC BY-SA v3.0 (as shown in documents associated with each of our creations). In accordance with the principles of the definition of Open Source Hardware (OSHW), we have signed it the 10th February 2011. We wish to contribute to the development of the ecosystem of “do it yourself” through original designs of products, uses and events.

Furthermore, all of their products are RoHS compliant and as part of the Open Hardware commitment, all the design files are available from the Snootlab website.

The subject of the review is the Snootlab Mémoire – an SD card data logging shield with on-board DS1307 real time clock [and matching backup battery] and prototyping area. It uses the standard SdFat library to write to normal SD memory cards formatted in FAT16 or FAT32. You can download the library from here. The real time clock IC is an easy to use I2C-interface model, and I have documented its use in great detail in this tutorial.

Once again, shield assembly is simple and quite straightforward. You can download an illustrated assembly guide from here, however it is in French. But everything you need to know is laid out on the PCB silk-screen, or the last page of the instructions. The it arrives in a reusable ESD bag:

… and all the required parts are included – including an IC socket and the RTC backup battery:

… the PCB is thick, with a very detailed silk-screen. Furthermore, it arrives with the SD card and 3.3V LDO (underneath) already pre-soldered – a nice touch:

The order of soldering the components is generally a subjective decision, and in this case I started with the resistors:

… and then worked my way out, but not fitting the battery nor IC until last. Intrestingly, the instructions require the crystal to be tacked down with some solder onto the PCB. Frankly I didn’t think it would withstand the temperature, however it did and all is well:

Which leaves us with a fully-assembled Mémoire shield ready for action:

Please note that a memory card is not included with the kit. If you are following along with your own Mémoire, the first thing to do after inserting the battery, IC and shield into your Arduino board and run some tests to ensure all is well. First thing is to test the DS1307 real-time clock IC. You can use the following sketch from chapter seven of my Arduino tutorial series:

If you are unsure about using I2C, please review my tutorial which can be found here. Don’t forget to update the time and date data in void setup(), and also comment out the setDateDS1307() function and upload the sketch a second time. The sketch output will be found on the serial monitor box – such as:

rtcdemooutput

Those of you familiar with the DS1307 RTC IC know that it can generate a nice 1 Hz pulse. To take advantage of this the SQW pin has an access hole on the PCB, beetween R10 and pin 8 of the IC:

For instruction on how to activate the SQW output, please visit the last section of this tutorial.

The next test is the SD card section of the shield. If you have not already done so, download and install the SdFat libary. Then, in the Arduino IDE, select File > Examples > SdFat > SdFatInfo. Insert the formatted (FAT16/32) SD card into the shield, upload the sketch, then open the serial monitor. You should be presented with something like this:

sdcardinfo

As you can see the sketch has returned various data about the SD card. Finally, let’s log some data. You can deconstruct the excellent example that comes with the SdFat library titled SdFatAnalogLogger (select File > Examples > SdFat > SdFatAnalogLogger). Using the functions:

you can “write” to the SD card in the same way as you would the serial output (that is, the serial monitor).

If you have reached this far without any errors – Congratulations! You’re ready to log. If not, remove the battery, SD card and IC from your shield (you used the IC socket, didn’t you?). Check the polarised components are in correctly, double-check your soldering and then reinsert the IC, shield and battery and try again. If that fails, support is available on the Snootlab website, and there is also a customer forum in French (use Google Translate). However as noted previously the team at Snootlab converse in excellent English and have been easy to contact via email if you have any questions. Stay tuned for the final Snootlab product review.

Snootlab products including the Snootlab Mémoire are available directly from their website. High-resolution images available on flickr.

As always, thank you for reading and I look forward to your comments and so on. Furthermore, don’t be shy in pointing out errors or places that could use improvement. Please subscribe using one of the methods at the top-right of this web page to receive updates on new posts, follow on twitterfacebook, or join our Google Group.

[Disclaimer - the products reviewed in this article are promotional considerations made available by Snootlab]

Posted in arduino, ds1307, education, kit review, snootlabComments (1)

Learn to solder with eevblog’s David L. Jones!

Hello Readers

How is your soldering? Have you always wanted to improve your soldering skills, or never heated an iron in your life and didn’t know where to start? No matter your level of skill you could do a lot worse than review the following video blogs in this article by David L. Jones.

Who? 

[David] shares some of his 20 years experience in the electronics design industry in his unique non-scripted naturally overly enthusiastic and passionate style.
Bullsh!t and political correctness don’t get a look-in.

Dave started out in hobby electronics over 30 years ago and since then has worked in such diverse areas as design engineering, production engineering, test engineering, electro-mechanical engineering, that wacky ISO quality stuff, field service, concept design, underwater acoustics, ceramic sensors, military sonar systems, red tape, endless paperwork trails, environmental testing, embedded firmware and software application design, PCB design (he’s CID certified), power distribution systems, ultra low noise and low power design, high speed digital design, telemetry systems, and too much other stuff he usually doesn’t talk about.

He has been published in various magazines including: Electronic Today International, Electronics Australia, Silicon Chip, Elektor, Everyday Practical Electronics (EPE), Make, and ReNew.

Few people know Dave is also a world renowned expert and author on Internet Dating, a qualified fitness instructor, geocacher, canyoner, and environmentalist.

Regular readers of this website would know that I rarely publish outside material – however the depth and quality of the tutorials make them a must-see for beginners and experienced people alike. Furthermore, if you have the bandwidth they can be viewed in 1080p. And as a fellow Australian I’m proud to support Dave and his efforts. So I hope you can view, enjoy and possibly learn from the following videos:

The first covers the variety of tools you would use:

And the second covers through-hole PCB soldering:

The third covers surface-mount soldering:

Finally, watch the procedure for soldering a tiny SMD IC using the ‘dead bug’ method:

And for something completely different:

If you enjoyed those videos then don’t forget to check out what’s new on Dave’s eevblog website and forum. Videos shown are (C) David L. Jones 2011 and embedded with permission.

As always, thank you for reading and I look forward to your comments and so on. Furthermore, don’t be shy in pointing out errors or places that could use improvement. Please subscribe using one of the methods at the top-right of this web page to receive updates on new posts, follow on twitterfacebook, or join our Google Group.

Posted in education, eevblog, hardware hacking, learning electronics, solderingComments (2)

Review: The Gravitech Arduino Nano family

Hello Readers

In this article we will examine a variety of products received for review from Gravitech in the United States – the company that designed and build the Arduino Nano. We have a Nano and some very interesting additional modules to have a look at.

So let’s start out review with the Arduino Nano. What is a Nano? A very, very small version of our Arduino Duemilanove boards. It contains the same microcontroller (ATmega328) but in SMD form; has all the I/O pins (plus two extra analogue inputs); and still has a USB interface via the FT232 chip. But more on that later. Nanos arrive in reusable ESD packaging which is useful for storage when not in use:

Patriotic Americans should note that the Nano line is made in the USA. Furthermore, here is a video clip of Nanos being made:

For those who were unsure about the size of the Nano, consider the following images:

You can easily see all the pin labels and compare them to your Duemilanove or Uno board. There is also a tiny reset button, the usual LEDs, and the in circuit software programmer pins. So you don’t miss out on anything by going to a Nano. When you flip the board over, the rest of the circuitry is revealed, including the FTDI USB>serial converter IC:

Those of you familiar with Arduino systems should immediately recognise the benefit of the Nano – especially for short-run prototype production. The reduction in size really is quite large. In the following image, I have traced the outline of an Arduino Uno and placed the Nano inside for comparison:

So tiny… the board measures 43.1mm (1.7″) by 17.8mm (0.7″). The pins on this example were pre-soldered – and are spaced at standard 2.54mm (0.1″) intervals – perfect for breadboarding or designing into your own PCB –  however you can purchase a Nano without the pins to suit your own mounting purposes. The Nano meets all the specifications of the standard Arduino Duemilanove-style boards, except naturally the physical dimensions.

Power can be supplied to the Nano via the USB cable; feeding 5V directly into the 5V pin, or 7~12 (20 max, not recommended) into the Vin pin. You can only draw 3.3V at up to 50 mA when the Nano is running on USB power, as the 3.3V is sourced from the FTDI USB>serial IC. And the digital I/O pins still allow a current draw up to 40 mA each. From a software perspective you will not have any problems, as the Nano falls under the same board classification as the (for example) Arduino Duemilanove:

Therefore one could take advantage of all the Arduino fun and games – except for the full-size shields. But as you will read soon, Gravitech have got us covered on that front. If the Arduino system is new to you, why not consider following my series of tutorials? They can be found here. In the meanwhile, to put the size into perspective – here is a short video of a Nano blinking some LEDs!

Now back to business. As the Nano does not use standard Arduino shields, the team at Gravitech have got us covered with a range of equivalent shields to enable all sorts of activities. The first of this is their Ethernet and microSD card add-on module:

and the underside:

Again this is designed for breadboarding, or you could most likely remove the pins if necessary. The microSD socket is connected as expected via the SPI bus, and is fully compatible with the default Arduino SD library. As shown in the following image the Nano can slot directly into the ethernet add-in module:

The Ethernet board requires an external power supply, from 7 to 12 volts DC. The controller chip is the usual Wiznet 5100 model, and therefore the Ethernet board is fully compatible with the default Ethernet Arduino library. We tested it with the example web server sketch provided with the Arduino IDE and it all just worked.

The next add-on module to examine is the 2MOTOR board:

… and the bottom:

Using this module allows control of two DC motors with up to two amps of current each via pulse-width modulation. Furthermore, there is a current feedback circuit for each motor so you measure the motor load and adjust power output – interesting. So a motorised device could sense when it was working too hard and ease back a little (like me on a Saturday). All this is made possible by the use of the common L298 dual full-bridge motor driver IC. This is quite a common motor driver IC and is easy to implement in your sketches. The use of this module and the Nano will help reduce the size of any robotics or motorised project. Stay tuned for use of this board in future articles.

Next in this veritable cornucopia of  add-on modules is the USBHOST board:

turning it over …

Using the Maxim MAX3421E host controller IC you can interface with all sorts of devices via USB, as well as work with the new Android ADK. The module will require an external power supply of between 7 and 12 volts DC, with enough current to deal with the board, a Nano and the USB device under control – one amp should be more than sufficient. I will be honest and note that USB and Arduino is completely new to me, however it is somewhat fascinating and I intend to write more about using this module in the near future. In the meanwhile, many examples can be found here.

For a change of scene there is also a group of Xbee wireless communication modules, starting with the Xbee add-on module:

The Xbee itself is not included, only shown for a size comparison. Turning the module over:

It is nice to see a clearly-labelled silk screen on the PCB. If you are unfamiliar with using the Xbee wireless modules for data communication, you may find my introductory tutorial of interest. Furthermore, all of the Gravitech Nano modules are fully software compatible with my tutorial examples, so getting started will be a breeze. Naturally Gravitech also produce an Xbee USB interface board, to enable PC communication over your wireless modules:

Again, note that the Xbee itself is not included, however they can be supplied by Gravitech. Turning the board over reveals another highly-detailed silk screen:

All of the Gravitech Xbee modules support both series 1.0 and 2.5 Xbees, in both standard and professional variants. The USB module also supports the X-CTU configuration software from Digi.

Finally – leaving possibly the most interesting part until last, we have the MP3 Player add-on board:

and on the B-side:

The MP3 board is designed around the VS1053B MP3 decoder IC. It can also decode Ogg Vorbis, AAC, WMA and MID files. There is a 3.5mm stereo output socket to connect headphones and so on. As expected, the microSD card runs from the SPI pins, however SS is pin 4. Although it may be tempting to use this to make a home-brew MP3 player, other uses could include: recorded voice messages for PA systems such as fire alarm notices, adding sound effects to various projects or amusement machines, or whatever else you can come up with.

Update – We have examined the MP3 board in more detail with a beginner’s tutorial.

The Arduino Nano and related boards really are tiny, fully compatible with their larger brethren, and will prove very useful. Although this article was an introductory review, stay tuned for further projects and articles that will make use of the Nano and other boards. If you have any questions or enquiries please direct them to Gravitech via their contact page. Gravitech products including the Arduino Nano family are available directly from their website or these distributors.

As always, thank you for reading and I look forward to your comments and so on. Furthermore, don’t be shy in pointing out errors or places that could use improvement. Please subscribe using one of the methods at the top-right of this web page to receive updates on new posts, follow on twitterfacebook, or join our Google Group.

[Disclaimer - the products reviewed in this article are promotional considerations made available by Gravitech]

High resolution photos are available on flickr.

Otherwise, have fun, be good to each other – and make something! 

Posted in arduino, ethernet, gravitech, microcontrollers, mp3, nano, part review, xbeeComments (0)

Tutorial: Arduino and a Thermal Printer

Use inexpensive thermal printers with Arduino in chapter thirty-eight of a series originally titled “Getting Started/Moving Forward with Arduino!” by John Boxall – a series of articles on the Arduino universe. The first chapter is here, the complete series is detailed here.

Updated 05/02/2013

In this article we introduce the inexpensive thermal printer that has recently become widely available from Sparkfun and their resellers. The goal of the article is to be as simple as possible so you can get started without any problems or confusion. In the past getting data from our Arduino to a paper form would either have meant logging it to an SD card then using a PC to finish the job, or perhaps viewing said data on an LCD then writing it down. Not any more – with the use of this cheap and simple serial printer. Before we get started, here is a short demonstration video of it in action:


Not bad at all considering the price. Let’s have a look in more detail. Here is the printer and two matching rolls of thermal paper:

… and the inside of the unit:

Loading paper is quite simple, just drop the roll in with the end of the paper facing away from you, pull it out further than the top of the front lip, then close the lid. The paper rolls required need to be 57mm wide and have a diameter of no more than 39mm. For example. There is a piece of white cardboard stuck to the front – this is an economical cover that hides some of the internals. Nothing of interest for us in there. The button next to the LED on the left is for paper advance, and the LED can blink out the printer status.

From a hardware perspective wiring is also very simple. Looking at the base of the printer:

… there are two connections. On the left is DC power, and data on the right. Thankfully the leads are included with the printer and have the plugs already fitted – a great time saver. You may also want to fit your own rubber feet to stop the printer rocking about.

Please note – you need an external power supply with a voltage of between 5 and 9 volts DC that can deliver up to 1.5 amps of current. When idling the printer draws less than 10 milliamps, but when printing it peaks at around 1.47 A. So don’t try and run it from your Arduino board. However the data lines are easy, as the printer has a serial interface we only need to connect printer RX to Arduino digital 3, and printer TX to Arduino digital 2, and GND to … GND! We will use a virtual serial port on pins 2 and 3 as 0 and 1 will be taken for use with the serial monitor window for debugging and possible control purposes.

If you want to quickly test your printer – connect it to the power, drop in some paper, hold down the feed button and turn on the power. It will quickly produce a test print.

Next we need to understand how to control the printer in our sketches. Consider this very simple sketch:

After ensuring your printer is connected as described earlier, and has the appropriate power supply and paper – uploading the sketch will result in the following:

Now that the initial burst of printing excitement has passed, let’s look at the sketch and see how it all works. The first part:

configures the virtual serial port and creates an instance for us to refer to when writing to the printer. Next, four variables are defined. These hold parameters used for configuring the printer. As the printer works with these settings there is no need to alter them, however if you are feeling experimental nothing is stopping you. Next we have the function initPrinter(). This sets a lot of parameters for the printer to ready itself for work. We call initPrinter() only once – in void setup(); For now we can be satisfied that it ‘just works’.

Now time for action – void loop(). Writing text to the printer is as simple as:

You can also use .println to advance along to the next line. Generally this is the same as writing to the serial monitor with Serial.println() etc. So nothing new there. Each line of text can be up to thirty-two characters in length.

The next thing to concern ourselves with is sending commands to the printer. You may have noticed the line

This sends the command to advance to the next line (in the old days we would say ‘carriage return and line feed’). There are many commands available to do various things.  At this point you will need to refer to the somewhat amusing user manual.pdf. Open it up and have a look at section 5.2.1 on page ten. Notice how each command has an ASCII, decimal and hexadecimal equivalent? We will use the decimal command values. So to send them, just use:

Easy. If the command has two or more values (for example, to turn the printer offline [page 11] ) – just send each value in a separate statement. For example:

… will put the printer into offline mode. Notice how we used the variable “zero” for 0 – you can’t send a zero by itself. So we assign it to the variable and send that instead. Odd.

For out next example, let’s try out a few more commands:

  • Underlined text (the printer seemed to have issues with thick underlining, however your experience may vary)
  • Bold text
  • Double height and width
Here is the sketch:

And the results:

Frankly bold doesn’t look that bold, so I wouldn’t worry about it too much. However the oversized characters could be very useful, and still print relatively quickly.

Next on our list are barcodes. A normal UPC barcode has 12 digits, and our little printer can generate a variety of barcode types – see page twenty-two of the user manual. For our example we will generate UPC-A type codes and an alphanumeric version. Alphanumeric barcodes need capital letters, the dollar sign, percent sign, or full stop. The data is kept in an array of characters named … barCode[]  and barCode[]2. Consider the functions printBarcode(), printBarcodeThick()  and printBarcodeAlpha() in the following example sketch:

Notice in printBarcodeThick() we make use of the ability to change the vertical size of the barcode – the height in pixels is the third parameter in the group. And here is the result:

So there you have it – another practical piece of hardware previously considered to be out of our reach – is now under our control. Now you should have an understanding of the basics and can approach the other functions in the user guide with confidence. Please keep in mind that the price of this printer really should play a large part in determining suitability for a particular task. It does have issues printing large blocks of pixels, such as the double-width underlining and inverse text. This printer is great but certainly not for commercial nor high-volume use. That is what professional POS printers from Brother, Star, Epson, etc., are for. However for low-volume, personal or hobby use this printer is certainly a deal. As always, now it is up to you and your imagination to put this to use or get up to other shenanigans.

This article would not have been possible without the example sketches provided by Nathan Seidle, the founder and CEO of Sparkfun. If you meet him, shout him a beer.  Please don’t knock off bus tickets or so on. I’m sure there are heavy penalties for doing so if caught.

LEDborder

Have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, COM-10438, COM-10560, education, lesson, microcontrollers, printer, sparkfun, thermal, tutorialComments (19)

Kit Reviews: Snootlab Power ScrewShield and I2C Power Protoshield

Hello Readers

In this article we will examine the first two products from a bundle sent for review by Snootlab, a Toulouse, France-based company that in their own words:

… designs and develops electronic products with an Open Hardware and Open Source approach. We are particularly specialized in the design of new shields for Arduino. The products we create are licensed under CC BY-SA v3.0 (as shown in documents associated with each of our creations). In accordance with the principles of the definition of Open Source Hardware (OSHW), we have signed it the 10th February 2011. We wish to contribute to the development of the ecosystem of “do it yourself” through original designs of products, uses and events.

Furthermore, all of their products are RoHS compliant and as part of the Open Hardware commitment, all the design files are available from the Snootlab website. First, let’s examine the Power Screwshield kit. This is a feature-laden prototyping shield suitable for Arduino Uno and compatible series boards. It can be used with the Mega, however not all of the I/O pins will be available.

Apart from obvious use as a prototyping shield, there are also three other useful features:

  • space for a 16-pin SOIC SMD part in the prototyping area;
  • a full line of screw terminals that connect to all the shield pin connections (in a similar way to the Wingshield Screwshield);
  • and a socket to allow power to be sourced from a standard computer ATX power supply, which brings 5V and 12V DC to the shield. I have never seen this implemented on a shield in the past – a very novel and useful idea.
If you are unfamiliar with the ATX power supply options, consider this image of the tronixstuff bench PC’s internals:
ldo3ss
The connector we would use is the one with the four round pins in a single row. In recent times using PC power supplies as bench power supply units has become quite common, so the designers at Snootlab have taken advantage of this in a very clever way by allowing their Power ScrewShield to use these power supplies. Assembly of the shield is simple and well documented. Although it is self-explanatory, you can download an illustrated guide from here. The kit is packaged in a reusable ESD bag:

bagss

Assembly of the shield is simple and well documented. Although it is self-explanatory, you can download an illustrated guide from here. The kit is packaged in a reusable ESD bag:

… which contains all the necessary parts:

partsss

… and a very high quality PCB:

pcbss

The PCB thickness is over 1mm, and as you can see from the image above the silk-screening describes all the areas of the PCB in a detailed manner. Note that this shield is much larger than a standard Arduino shield – this becomes obvious when compared with a standard prototyping shield:

pcbcompss

Assembly was very smooth and quick. There are a couple of things to watch out for, for example you need to slide the terminal blocks together so that they are flush on the sides, such as:

blocks

… if you want to enable the 12V DC rail from the ATX power lead, short out the jumper SJ1 with a blob of solder:

enable12vss

… when soldering the PC power connector, be sure to make the clamp bracket flush with the socket, for example:

atxss

… and finally, to enable use of the shield’s LED, you need to cut the track in this area on the underside of the PCB:

Although at first the introduction of another Arduino prototyping shield may not have seemed that interesting – this version from Snootlab really goes all out to cover almost every possible need in a shield all at the same time. Sure, it is a lot larger – but none of the board space is wasted – and those terminal blocks would be very hand for making some more permanent-style prototypes with lots of external wiring.  And the ability to accept power from a PC ATX-style power supply unit is certainly original and possibly very useful depending on your application. So if you need to create something that needs a lot of power, a lot of prototyping space, and a lot of wiring – this is the protoshield for you.

For the second half of the review we have the Snootlab I2C Power Protoshield. This is another example of an Arduino prototyping shield with some interesting twists. Apart from employing the same PC power connector as used with the Power ScrewShield, this shield is designed for hard-core I2C-bus enthusiasts. (What’s I2C? Check my tutorials). This is due to the 10-pin HE connector on the edge of the board – it contains pins for SCL, SDA, 3.3V, 5V and GND. With this you could use you own cable connections to daisy-chain other devices communicating via the I2C bus. Again, the shield is a kit and assembly was simple.

Like other Snootlab products, the kit arrives in a reusable ESD bag:

bag

… with a high-quality thick PCB that has a very detailed silk-screen layer:

pcb

… and all the required parts are included:

parts1

When soldering in the shield connectors, using another shield as a jig can save time:

headers

And we’re finished:

finished

One could also mount a small solderless breadboad on the I2C Power Protoshield:

finishedwithbreadboard

One great feature is the inclusion of an NCP1117DT33 3.3V 1A voltage regulator. Using this you can source 3.3 volts at up to one amp of current (only) when using the PC power supply connection. This is a great idea, as in the past it can be too easy to accidentally burn out the FTDI chip on an Arduino Duemilanove by drawing too much current from the 3.3V pin. The use of the external 3.3V supply is controlled by a jumper on the header pins here:

intext3v3

Finally, in the image above you can see the area for external I2C pull-up resistors. Generally with our Arduino the internal pull-up resistors in the microcontroller are adequate, however with many I2C devices in use (e.g. eight 24LC512 EEPROMS!) external pull-ups are required.

After examining the two shields I am impressed with the quality of the components and PCBs, as well as the interesting features described in the review. Theyare certainly unique and very much useful if required, especially the PC power supply connections. Support is available on the Snootlab website, and there is also a customer forum in French (use Google Translate). However the people at Snootlab converse in excellent English and have been easy to contact via email if you have any questions. Stay tuned for more interesting Snootlab product reviews.

Snootlab products including the I2C Power Protoshield and the Power ScrewShield are available directly from their website.

As always, thank you for reading and I look forward to your comments and so on. Furthermore, don’t be shy in pointing out errors or places that could use improvement. Please subscribe using one of the methods at the top-right of this web page to receive updates on new posts, follow on twitterfacebook, or join our Google Group.

[Disclaimer - the products reviewed in this article are promotional considerations made available by Snootlab]

Posted in arduino, kit review, microcontrollers, snootlabComments (13)

Project – Single button combination lock

Time for something different  – a single button combination lock. Allow me to explain…

Updated 18/03/2013

Normally a combination lock would require the entry of a series of unique numbers in order to unlock something or start an action. For example:

800px-masterpadlock

(image information)

A more contemporary type of lock could be controlled electronically, for example by a keypad where the user enters a series of digits to cause something to happen. Such as the keypad on this dodgy $30 safe from Officeworks:

As you can see there is a button for each digit. You would think that this would be a good idea –  however people can watch you enter the digits, or users can be silly enough to write down the combination somewhere. In some cases the more cunning monkeys have even placed cameras that can observe keypads to record people entering the combination. There must be a better way. Possibly! However in the meanwhile you can consider my idea instead – just have one button. Only one button – and the combination is made up of the time that elapses between presses of the button. There are many uses for such an odd lock:

  • A type of combination lock that controls an electric door strike, or activates a device of some sort;
  • A way of testing mind-hand coordination for skill, or the base of a painfully frustrating game;
  • Perhaps an interlock on motor vehicle to prevent drink driving. After a few drinks there’s no way you could get the timing right. Then again, after a double espresso or two you might have problems as well.
How does it work? Consider the following:

We measure the duration of time between each press of the button (in this case – delay 1~4). These delay times are then compared against values stored in the program that controls the lock. It is also prudent to allow for some tolerance in the user’s press delay – say plus or minus ten to fifteen percent. We are not concerned with the duration of each button press, however it is certainly feasible.

To create this piece of hardware is quite easy, and once again we will use the Arduino way of doing things. For prototyping and experimenting it is simple enough to create with a typical board such as a Uno or Eleven and a solderless breadboard – however to create a final product you could minimise it by using a bare-bones solution (as described here). Now let’s get started…

For demonstration purposes we have a normally-open button connected to digital pin 2 on our Arduino-compatible board using the 10k ohm pull down resistor as such:

democircuit

The next thing to do is determine our delay time values. Our example will use five presses, so we measure four delays. With the following sketch, you can generate the delay data by pushing the button yourself – the sketch will return the delay times on the serial monitor:

So what’s going on the this sketch? Each time the button is pressed a reading of millis() is taken and stored in an array. [More on millis() in the tutorial]. Once the button has been pressed five times, the difference in time between each press is calculated and stored in the array del[]. Note the use of a 500 ms delay in the function dataCapture(), this is to prevent the button bouncing and will need to be altered to suit your particular button. Finally the delay data is then displayed on the serial monitor. For example:

The example was an attempt to count one second between each press. This example also illustrates the need to incorporate some tolerance in the actual lock sketch. With a tolerance of +/- 10% and delay values of one second, the lock would activate. With 5% – no. Etcetera.

Now for the lock sketch. Again it measures the millis() value on each button press and after five presses calculates the duration between each press. Finally in the function checkCombination() the durations are compared against the stored delay values (generated using the first sketch) which are stored in the array del[]. In our example lock sketch we have values of one second between each button press. The tolerance is stored as a decimal fraction in the variable tolerance; for example to have a tolerance of ten percent, use 0.1:

When choosing your time delays, ensure they are larger than the value used for button debounce (the delay() function call) in the dataCapture() function. Notice the two functions success() and failure() – these will contain the results of what happens when the user successfully enters the combination or does not. For a demonstration of the final product, I have connected an LCD to display the outcomes of the entry attempts. You can download the sketch from here. The key used in this example is 1,2,3,4 seconds:

Although there are four buttons on the board used in the video, only one is used. Well I hope someone out there found this interesting or slightly useful…

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, combination lock, education, learning electronics, lesson, microcontrollers, millis, projects, tutorial, twitterComments (6)

Tutorial: Arduino timing methods with millis()

This is chapter thirty-seven of a series originally titled “Getting Started/Moving Forward with Arduino!” by John Boxall – in what feels like an endless series of articles on the Arduino universe. The first chapter is here, the complete series is detailed here. Any files from tutorials will be found here.

[Updated 20/01/2013]

In this article we introduce the millis(); function and put it to use to create various timing examples.

Millis? Nothing to do with lip-syncers… hopefully you recognised milli as being the numerical prefix for one-thousandths; that is multiplying a unit of measure by 0.001 (or ten to the power of negative 3). Interestingly our Arduino systems will count the number of milliseconds (thousands of a second) from the start of a sketch running until the count reaches the maximum number capable of being stored in the variable type unsigned long (a 32-bit [four byte] integer – that ranges from zero to (2^32)-1.

(2^32)-1, or 4294967295 milliseconds converts to 49.71027-odd days. The counter resets when the Arduino is reset, it reaches the maximum value or a new sketch is uploaded. To get the value of the counter at a particular juncture, just call the function – for example:

Where start is an unsigned long variable. Here is a very simple example to show you millis() in action:

The sketch stores the current millis count in start, then waits one second, then stores the value of millis again in finished. Finally it calculates the elapsed time of the delay.  In the following screen dump of the serial monitor, you can see that the duration was not always exactly 1000 milliseconds:

To put it simply, the millis function makes use of an internal counter within the ATmega microcontroller at the heart of your Arduino. This counter increments every clock cycle – which happens (in standard Arduino and compatibles) at a clock speed of 16 Mhz. This speed is controlled by the crystal on the Arduino board (the silver thing with T16.000 stamped on it):

Crystal accuracy can vary depending on external temperature, and the tolerance of the crystal itself. This in turn will affect the accuracy of your millis result. Anecdotal experience has reported the drift in timing accuracy can be around three or four seconds per twenty-four hour period. If you are using a board or your own version that is using a ceramic resonator instead of a crystal, note that they are not as accurate and will introduce the possibility of higher drift levels. If you need a much higher level of timing accuracy, consider specific timer ICs such as the Maxim DS3232.

Now we can make use of the millis  for various timing functions. As demonstrated in the previous example sketch, we can calculate elapsed time. To take this idea forward, let’s make a simple stopwatch. Doing so can be as simple or as complex as necessary, but for this case we will veer towards simple. On the hardware perspective, we will have two buttons – Start and Stop – with the 10k ohm pull-down resistors connected to digital pins 2 and 3 respectively.

When the user presses start the sketch will note the value for millis – then after stop is pressed, the sketch will again note the value for millis, calculate and display the elapsed time. The user can then press start to repeat the process, or stop for updated data. Here is the sketch:

The calls to delay() are used to debounce the switches – these are optional and their use will depend on your hardware. Below is an example of the sketch’s serial monitor output – the stopwatch has started, and then button two pressed six times across periods of time:

If you had a sensor at the start and end of a fixed distance, speed could be calculated: speed = distance ÷ time.

You can also make a speedometer for a wheeled form of motion, for example a bicycle. At the present time I do not have a bicycle to mess about with, however we can describe the process to do so – it is quite simple. (Disclaimer – do so at your own risk etc.)  First of all, let’s review the necessary maths. You will need to know the circumference of the wheel. Hardware – you will need a sensor. For example – a reed switch and magnet. Consider the reed switch to be a normally-open button, and connect as usual with a 10k ohm pull-down resistor. Others may use a hall-effect sensor – each to their own). Remember from maths class:

(image licence)

To calculate the circumference – use the formula:

circumference = 2πr 

where r is the radius of the circle. Now that you have the wheel circumference, this value can be considered as our ‘fixed distance’, and therefore the speed can be calculated by measuring the elapsed time between of a full rotation.

Your sensor – once fitted – should act in the same method as a normally-open button that is pushed every rotation. Our sketch will measure the time elapsed between every pulse from the sensor. To do this, our example will have the sensor output connected to digital pin 2 – as it will trigger an interrupt to calculate the speed. (Interrupts? See chapter three). The sketch will otherwise be displaying the speed on a normal I2C-interface LCD module. The I2C interface is suggested as this requires only 4 wires from the Arduino board to the LCD – the less wires the better.

Here is the sketch for your perusal:

There isn’t that much going on – every time the wheel completes one revolution the signal from the sensor will go from low to high – triggering an interrupt which calls the function speedCalc(). This takes a reading of millis() and then calculates the difference between the current reading and the previous reading – this value becomes the time to cover the distance (which is the circumference of the wheel relative to the sensor – stored in

and is measured in metres). It finally calculates the speed in km/h and MPH. Between interrupts the sketch displays the updated speed data on the LCD as well as the raw time value for each revolution for curiosity’s sake. In real life I don’t think anyone would mount an LCD on a bicycle, perhaps an LED display would be more relevant.

In the meanwhile, you can see how this example works in the following short video clip. Instead of a bike wheel and reed switch/magnet combination, I have connected the square-wave output from a function generator to the interrupt pin to simulate the pulses from the sensor, so you can get an idea of how it works:

That just about sums up the use of millis() for the time being. There is also the micros(); function which counts microseconds. So there you have it – another practical function that can allow more problems to be solved via the world of Arduino. As always, now it is up to you and your imagination to find something to control or get up to other shenanigans.

LEDborder

Have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, education, learning electronics, lesson, microcontrollers, millis, speedometer, stopwatch, timing, tutorialComments (18)

Tutorial: Arduino and the SPI bus part II

This is chapter thirty-six of a series originally titled “Getting Started/Moving Forward with Arduino!” by John Boxall – A seemingly endless series of articles on the Arduino universe. The first chapter is here, the complete series is detailed here

[Updated 10/01/2013]

This is the second of several chapters in which we are investigating the SPI data bus, and how we can control devices using it with our Arduino systems. If you have not done so already, please read part one of the SPI articles. Again we will learn the necessary theory, and then apply it by controlling a variety of devices. As always things will be kept as simple as possible.

First on our list today is the use of multiple SPI devices on the single bus. We briefly touched on this in part one, by showing how multiple devices are wired, for example:

Notice how the slave devices share the clock, MOSI and MISO lines – however they both have their own chip select line back to the master device. At this point a limitation of the SPI bus becomes prevalent – for each slave device we need another digital pin to control chip select for that device. If you were looking to control many devices, it would be better to consider finding I2C solutions to the problem. To implement multiple devices is very easy. Consider the example 34.1 from part one – we controlled a digital rheostat. Now we will repeat the example, but instead control four instead of one. For reference, here is the pinout diagram:

Doing so may sound complex, but it is not. We connect the SCK, MOSI and  MISO pins together, then to Arduino pins D13, D11, D12 respectively. Each CS pin is wired to a separate Arduino digital pin. In our example rheostats 1 to 4 connect to D10 through to D7 respectively. To show the resistance is changing on each rheostat, there is an LED between pin 5 and GND and a 470 ohm resistor between 5V and pin 6. Next, here is the sketch:

Although the example sketch may be longer than necessary, it is quite simple. We have four SPI devices each controlling one LED, so to keep things easy to track we have defined led1~led4 to match the chip select digital out pins used for each SPI device. Then see the first four lines in void setup(); these pins are set to output in order to function as required. Next – this is very important – we set the pins’ state to HIGH. You must do this to every chip select line! Otherwise more than one CS pins may be initially low in some instances and cause the first data sent from MOSI to travel along to two or more SPI devices. With LEDs this may not be an issue, but for motor controllers … well it could be.

The other point of interest is the function

We pass the value for the SPI device we want to control, and the value to send to the device. The value for l is the chip select value for the SPI device to control, and ranges from 10~7 – or as defined earlier, led1~4. The rest of the sketch is involved in controlling the LED’s brightness by varying the resistance of the rheostats. Now to see example 36.1 in action via the following video clip:


(If you are wondering what I have done to the Freetronics board in that video, it was to add a DS1307 real-time clock IC in the prototyping section).

Next on the agenda is a digital-to-analogue converter, to be referred to using the acronym DAC. What is a DAC? In simple terms, it accepts a numerical value between zero and a maximum value (digital) and outputs a voltage between the range of zero and a maximum relative to the input value (analogue). One could consider this to be the opposite of the what we use the function analogRead(); for. For our example we will use a Microchip MCP4921 (data sheet.pdf):

(Please note that this is a beginners’ tutorial and is somewhat simplified). This DAC has a 12-bit resolution. This means that it can accept a decimal number between 0 and 4095 – in binary this is 0 to 1111 1111 1111 (see why it is called 12-bit) – and the outpout voltage is divided into 4096 steps. The output voltage for this particular DAC can fall between 0 and just under the supply voltage (5V). So for each increase of 1 in the decimal input value, the DAC will output around 1.221 millivolts.

It is also possible to reduce the size of the voltage output steps by using a lower reference voltage. Then the DAC will consider the reference voltage to be the maximum output with a value of 4095. So (for example) if the reference voltage was 2.5V, each increase of 1 in the decimal input value, the DAC will output around 0.6105 millivolts. The minimum reference voltage possible is 0.8V, which offers a step of 200 microvolts (uV).

The output of a DAC can be used for many things, such as a function generator or the playback of audio recorded in a digital form. For now we will examine how to use the hardware, and monitoring output on an oscilloscope. First we need the pinouts:

By now these sorts of diagrams shouldn’t present any problems. In this example, we keep pin 5 permanently set to GND; pin 6 is where you feed in the reference voltage – we will set this to +5V; AVss is GND; and Vouta is the output signal pin – where the magic comes from :) The next thing to investigate is the MCP4921’s write command register:

Bits 0 to 11 are the 12 bits of the output value; bit 15 is an output selector (unused on the MPC4921); bit 14 controls the input buffer; bit 13 controls an inbuilt output amplifier; and bit 12 can shutdown the DAC. Unlike previous devices, the input data is spread across two bytes (or a word of data). Therefore a small amount of work needs to be done to format the data ready for the DAC. Let’s explain this through looking at the sketch for example 36.2 that follows. The purpose of the sketch is to go through all possible DAC values, from 0 to 4095, then back to 0 and so on.

First. note the variable outputvalue – it is a word, a 16-bit unsigned variable. This is perfect as we will be sending a word of data to the DAC. We put the increasing/decreasing value for a into outputValue. However as we can only send bytes of data at a time down the SPI bus, we will use the function highbyte() to separate the high side of the word (bits 15~8) into a byte variable called data.

We then use the bitwise AND and OR operators to set the parameter bits 15~12. Then this byte is sent to the SPI bus. Finally, the function lowbyte() is used to send the low side of the word (bits 7~0) into data and thence down the SPI bus as well.

Now for our demonstration sketch:

And a quick look at the DAC in action via an oscilloscope:

By now we have covered in detail how to send data to a device on the SPI bus. But how do we receive data from a device?

Doing so is quite simple, but some information is required about the particular device. For the rest of this chapter, we will use the Maxim DS3234 “extremely accurate” real-time clock. Please download the data sheet (.pdf) now, as it will be referred to many times.

The DS3234 is not available in through-hole packaging, so we will be using one that comes pre-soldered onto a very convenient breakout board:

It only takes a few moments to solder in some header pins for breadboard use. The battery type is CR1220 (12 x 2.0mm, 3V); if you don’t have a battery you will need to short out the battery holder with some wire otherwise the IC will not work. Readers have reported that the IC doesn’t keep time if the USB and external power are both applied to the Arduino at the same time.

A device will have one or more registers where information is read from and written to. Look at page twelve of the DS3234 data sheet, there are twenty-three registers, each containing eight bits (one byte) of data. Please take note that each register has a read and write address. An example – to retrieve the contents of the register at location 08h (alarm minutes) and place it into the byte data we need to do the following:

Don’t forget to take note of  the function SPI.setBitOrder(MSBFIRST); in your sketch, as this also determines the bit order of the data coming from the device. To write data to a specific address is also quite simple, for example:

Up to this point, we have not concerned ourselves with what is called the SPI data mode. The mode determines how the SPI device interprets the ‘pulses’ of data going in and out of the device. For a well-defined explanation, please read this article. With some devices (and in our forthcoming example) the data mode needs to be defined. So we use:

to set the data mode, within void(setup);. To determine a device’s data mode, as always – consult the data sheet. With our DS3234 example, the mode is mentioned on page 1 under Features List.

Finally, let’s delve a little deeper into SPI via the DS3234. The interesting people at Sparkfun have already written a good demonstration sketch for the DS3234, so let’s have a look at that and deconstruct it a little to see what is going on. You can download the sketch below from here, then change the file extension from .c to .pde.

Don’t let the use of custom functions and loops put you off, they are there to save time. Looking in the function SetTimeDate();, you can see that the data is written to the registers 80h through to 86h (skipping 83h – day of week) in the way as described earlier (set CS low, send out address to write to, send out data, set CS high). You will also notice some bitwise arithmetic going on as well. This is done to convert data between binary-coded decimal and decimal numbers.

Why? Go back to page twelve of the DS3234 data sheet and look at (e.g.) register 00h/80h – seconds. The bits 7~4 are used to represent the ‘tens’ column of the value, and bits 3~0 represent the ‘ones’ column of the value. So some bit shifting is necessary to isolate the digit for each column in order to convert the data to decimal. For other ways to convert between BCD and decimal, see the examples using the Maxim DS1307 in chapter seven.

Finally here is another example of reading the time data from the DS3234:

So there you have it – more about the world of the SPI bus and how to control the devices within.

LEDborder

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, BOB-10160, dac, DS3234, education, learning electronics, lesson, MCP4162, MCP4921, microcontrollers, SPI, tutorial, UncategorizedComments (13)

Tutorial: Video output from your Arduino

Create video output from your Arduino in chapter 35 of tutorials about the Arduino universe. The first chapter is here, the complete series is detailed here.

[Updated 10/01/2013]

In this chapter we will examine something different – the ability of our Arduino and compatible boards to create composite video output. In other words, displaying stuff from the Arduino on a TV. A lot of people were unaware of the ability to do this, however the process is very simple and not difficult to implement from a hardware perspective. Within this chapter we will learn to construct the minimum hardware required and demonstrate basic functions to get started.

To whet your appetite, here is a quick video demonstration of what is possible:

You can’t expect too much from a 16 MHz microcontroller without a video card… but the price is right, and with some imagination and the right functions you can do quite well. To make this happen we need to knock out some hardware of our own. Connection is very easy. First we need to locate three pins on our Arduino board. They will be used to output Sync, Video and also GND. For those with Arduino Uno/Freetronics Eleven etc Sync is digital 9, video is digital 7 and GND is … GND. If you have a Mega/Mega2560 Sync is digital 11 and video is A7. There is also the ability to generate audio with the methods in this article, and if you want to do this the Uno (etc.) pin is digital 11 or 10 on the Mega.

The monitor or television used needs to have a composite video-in socket (jack). For those with older televisions that have a VCR connected, you could use the video-in socket on the VCR. The schematic for video out is very simple, you only need two normal 0.25W resistors and a video lead:

If you’re not up for soldering into an RCA plug, a simple way is to chop up a standard video lead as such:

Then just wire the termination of the two resistors to the centre core (“pin”) and GND to the shield. For the purpose of this article I have made a quick TV-out shield that also includes a thumb joystick (as reviewed here).

A real triumph of engineering… however it solves the problem. The vertical trimmer is connected to A0;  the horizontal to A1; the button to digital 8 via a 10k0 pull-up resistor. Next, you will need to download and install the arduino-tvout library. It can be found here. We will use the TVoutBeta1.zip version.  Those of you who may have a nootropic design Hackvision – please note your library is different.

Now to see how to integrate TV-out into our sketch. We will run through the basic functions which integrated with your imagination should see some interesting results…  So let’s go!

For every project, place these two lines at the top of your sketch:

The first brings in the library, and the second line creates an instance of TV to use with the library functions. Next, we need to activate TVout and select the appropriate broadcast standard (PAL or NTSC). In void setup() use either

Now for the main functions. The first one of interest will be:

which … clears the screen. Or if you would like to fill the screen with white, use

Moving on – to write some text. First we need to select a font. There are three basic fonts to choose from:

  • font4x6 (each character being 4 pixels by 6 pixels, etc.)
  • font6x8
  • font8x8

Well there is four, but it wouldn’t display for me. Working on it! To choose a font use:

Then to write the text, choose the screen location with:

then display the text with:

You can also use TV.println(); to add a carriage return as expected. Display single characters with a position in the one function using:

So let’s have a look at the various fonts in action with the following sketch:

 

Now to move into the 1970s with some basic graphical functions. We have a screen resolution of 128 by 96 pixels to work with. When planning your display, you need to ensure that the sketch never attempts to display a pixel outside of the 128 x 96 screen area. Doing so generally causes the Arduino to reboot.

First let’s start with basic pixels. To draw a pixel, use:

where x and y are the coordinates of the pixel, and z is the colour (1 = white, 0 = black, 2 = inverse of current pixel’s colour). You want more than a pixel? How about a line:

Draws a line from x1, y1 to x2, y2 of colour colour. (1 = white, 0 = black, 2 = inverse of current pixel’s colour).

Rectangles? Easy:

Draws a rectangle with the top-left corner at x,y; width w, height h, colour and optional fill colour. Circles are just as simple:

Draws a circle with centre at x,y; radius r pixels, edge colour, optional fill colour.

Now to see these functions in action with the following sketch: