Tag Archive | "mosfet"

Experimenting with Arduino and IKEA DIODER LED Strips

Introduction

A few weeks ago I found a DIODER LED strip set from a long-ago trek to IKEA, and considered that something could be done with it.  So in this article you can see how easy it is to control the LEDs using an Arduino or compatible board with ease… opening it up to all sorts of possibilities.

This is not the most original project – however things have been pretty quiet around here, so I thought it was time to share something new with you. Furthermore the DIODER control PCB has changed, so this will be relevant to new purchases. Nevertheless, let’s get on with it.

So what is DIODER anyhow? 

As you can see in the image below, the DIODER pack includes four RGB LED units each with nine RGB LEDs per unit. A controller box allows power and colour choice, a distribution box connects between the controller box and the LED strips, and the whole thing is powered by a 12V DC plugpack:

IKEA DIODER LED strips

The following is a quick video showing the DIODER in action as devised by IKEA:

 

Thankfully the plugpack keeps us away from mains voltages, and includes a long detachable cable which connects to the LED strip distribution box. The first thought was to investigate the controller, and you can open it with a standard screwdriver. Carefully pry away the long-side, as two clips on each side hold it together…

IKEA DIODER Arduino tronixstuff
… which reveals the PCB. Nothing too exciting here – you can see the potentiometer used for changing the lighting effects, power and range buttons and so on:

ikea dioder tronixstuff arduino

Our DIODER has the updated PCB with the Chinese market microcontroller. If you have an older DIODER with a Microchip PIC – you can reprogram it yourself.

ikea dioder arduino tronixstuff

The following three MOSFETs are used to control the current to each of the red, green and blue LED circuits. These will be the key to controlling the DIODER’s strips – but are way too small for me to solder to. The original plan was to have an Arduino’s PWM outputs tap into the MOSFET’s gates – but instead I will use external MOSFETs.

ikea dioder arduino tronixstuff

So what’s a MOSFET?

In the past you may have used a transistor to switch higher current from an Arduino, however a MOSFET is a better solution for this function. The can control large voltages and high currents without any effort. We will use N-channel MOSFETs, which have three pins – Source, Drain and Gate. When the Gate is HIGH, current will flow into the Drain and out of the Source:

mosfet

A simplistic explanation is that it can be used like a button – and when wiring your own N-MOSFET a 10k resistor should be used between Gate and Drain to keep the Gate low when the Arduino output is set to LOW (just like de-bouncing a button). To learn more about MOSFETS – get yourself a copy of “The Art of Electronics“. It is worth every cent.

However being somewhat time poor (lazy?), I have instead used a Freetronics NDrive Shield for Arduino – which contains six N-MOSFETs all on one convenient shield  – with each MOSFET’s Gate pin connected to an Arduino PWM output.
freetronics ndrive shield tronixlabs

So let’s head back to the LED strips for a moment, in order to determine how the LEDs are wired in the strip. Thanks to the manufacturer – the PCB has the markings as shown below:

ikea dioder tronixstuff arduino

They’re 12V LEDs in a common-anode configuration. How much current do they draw? Depends on how many strips you have connected together…

ikea dioder arduino tronixstuff

For the curious I measured each colour at each length, with the results in the following table:

current

So all four strips turned on, with all colours on – the strips will draw around 165 mA of current at 12V. Those blue LEDs are certainly thirsty.

Moving on, the next step is to connect the strips to the MOSFET shield. This is easy thanks to the cable included in the DIODER pack, just chop the white connector off as shown below:

ikea dioder arduino tronixstuff

By connecting an LED strip to the other end of the cable you can then determine which wire is common, and which are the cathodes for red, green and blue.

The plugpack included with the DIODER pack can be used to power the entire project, so you will need cut the DC plug (the plug that connects into the DIODER’s distribution box) off the lead, and use a multimeter to determine which wire is negative, and which is positive.

Connect the negative wire to the GND terminal on the shield, and the positive wire to the Vin terminal.  Then…

  • the red LED wire to the D3 terminal,
  • the green LED wire to the D9 terminal,
  • and the blue LED wire to the D10 terminal.

Finally, connect the 12V LED wire (anode) into the Vin terminal. Now double-check your wiring. Then check it again.

ikea dioder tronixstuff arduino

Testing

Now to run a test sketch to show the LED strip can easily be controlled. We’ll turn each colour on and off using PWM (Pulse-Width Modulation) – a neat way to control the brightness of each colour. The following sketch will pulse each colour in turn, and there’s also a blink function you can use.

Success. And for the non-believers, watch the following video:

Better LED control

As always, there’s a better way of doing things and one example of LED control is the awesome FASTLED library by Daniel Garcia and others. Go and download it now – https://github.com/FastLED/FastLED. Apart from our simple LEDS, the FASTLED library is also great with WS2812B/Adafruit NeoPixels and others.

One excellent demonstration included with the library is the AnalogOutput sketch, which I have supplied below to work with our example hardware:

You can see this in action through the following video:

Control using a mobile phone?

Yes – click here to learn how.

Conclusion

So if you have some IKEA LED strips, or anything else that requires more current than an Arduino’s output pin can offer – you can use MOSFETs to take over the current control and have fun. And finally a plug for my own store – tronixlabs.com – offering a growing range and Australia’s best value for supported hobbyist electronics from adafruit, DFRobot, Freetronics, Seeed Studio and much much more.

visit tronixlabs.com

As always, have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our forum – dedicated to the projects and related items on this website.

Posted in arduino, freetronics, Ikea, MOSFET, tronixlabs, tronixstuff, tutorialComments (3)

Review – Freetronics Module Family

Hello

In this article we examine a new range of eleven electronic modules from Freetronics. When experimenting with electronics or working on a prototype of a design, the use of electronic components in module form can make construction easier, and also reduce the time between thoughts and actually making something 🙂 So let’s have a look at each module in more detail…

PoE Power Regulator – 28V

This is a tiny switchmode voltage regulator with two uses – the first being regulation of higher voltage up to 28V carried via an Ethernet cable to a Freetronics Ethernet shield or EtherTen to power the board itself. The PCB is designed to drop into the shield or EtherTen as such:

… and converts the incoming voltage down to 7V which can be regulated by the EtherTen’s inbuilt regulator. The second use of this board is a very handy power supply for breadboarding or other experimentation. By bridging the solder pads on the rear of the board, the output is set to 5V DC, as such:

Note the addition of the header pins, which make insertion into a breadboard very easy – so now you have a 5V 1A DC power supply. For more information visit the product page.

N-MOSFET Driver/Output Module

This module contains an On Semi NTD5867NL MOSFET which allows the switching of a high current and voltage line – 60V at up to 20A – with a simple Arduino or other MCU digital output pin. The package is small and also contains enlarged holes for direct connection of high-current capability wire:

The onboard circuitry includes a pull-down resistor to ensure the MOSFET is off by default. For more information see the product page.

Logic Level Converter Module

This is a very simple and inexpensive method to interface 3.3V sensors to 5V microcontrollers in either direction.The module contains four independent channels, as shown in the image below:

However you can interface any low or higher voltage, as long as you connect the low and high voltages to the correct sides (marked on the PCB’s silk screen). For more information please visit the product page.

RGBLED Module

Surprisingly this module contains a RGB LED module (red, green and blue LEDs) which is controlled by a WS2801 constant-current LED driver IC. This module is only uses two digital output pins, and can be daisy-chained to control many modules with the same two pins. The connections are shown clearly on the module:

The WS2801 controller IC is on the rear:

There are several ways to control the LEDs. One way is using the sketch from the product home page, which results with the following demonstration output:

Or there is a unique Arduino WS2801 library available for download from here. Using the strandtest example included with the library results with the following:

During operation the module used less than 24 mA of current and therefore can happily run from a standard Arduino-type board without any issues. For more information please visit the product page.

TEMP Temperature Sensor Module

This module allows the simple measurement of temperature using the popular DS18B20 temperature sensor. You can measure temperatures between -55° and 125°C with an accuracy of +/- 0.5°C. Furthermore as the sensor uses the 1-wire bus, you can daisy-chain more than one sensor for multiple readings in the one application. The board is simple to use, and also contains a power-on LED:

Using the demonstation Arduino sketch from the product page results in the following output via the serial monitor:

Using this module is preferable to the popular Analog Devices TMP36, as it has an analogue output which can be interfered with, and requires an analogue input pin for each sensor, whereas this module has a digital output and as mentioned previously can be daisy-chained. For more information please visit the product page.

Humidity and Temperature Sensor Module

For the weather-measuring folk here is a module with temperatures and humidity. Using the popular DHT22 sensor module the temperature range is -4°C to +125°C with an accuracy of +/- 0.5°C, and humidity with an accuracy of between two and five percent. Only one digital input pin is required, and the board is clearly labelled:

There is also a blue power-on LED towards the top-right of the sensor. Using the module is quite simple with Arduino – download and use the example sketch included in the sensor library you can download from here. For the demonstration connect the centre data pin to Arduino digital two. Here is an example of the demonstration output:

Although the update speed is not lightning-fast, this should not be an issue unless you’re measuring real-time external temperature of your jet or rocket. For more information please see the product page.

Shift Register/Expansion Module

This board uses a 74HC595 serial-in parallel-out shift register which enables you to control eight digital outputs with only three digital pins, for example:

You can daisy-chain these modules to increase the number of digital outputs in multiples of eight, all while only using the three digital output pins on your Arduino or other microcontroller. For more information about how to use shift registers with Arduino systems, read our detailed tutorial. Otherwise for more information about the module please visit the product page.

Hall Effect Magnetic and Proximity Sensor Module

This module contains a sensor which changes output from HIGH to LOW when a magnetic presence is detected, for example a magnet. The board also has an LED which indicates the presence of the magnet to aid in troubleshooting:

Using this module and a small magnet would be an easy way to create a speedometer for a bicycle, the module is mounted to the fork, and the magnet on the rim of the front wheel. For more ideas consider the speedometer project in this tutorial. Otherwise for more information about this module please visit the product page.

Microphone Sound Input Module

This module performs two functions – it can return the sound pressure level (SPL) or the amplified audio waveform from the electret microphone. The LED (labelled “DETECT”) on the board visually displays an approximation of the SPL – for example:

… however the value can be returned by using an analogue input pin on an Arduino (etc). to return a numerical value. To do this connect the SPL pin to the analogue input. The MIC pin is used to take the amplified output from the microphone, to be processed by an ADC or used in an audio project. For more information please visit the product page.

Light Sensor Module

This module uses the TEMT6000 light sensor which returns more consistent values than can be possible using a light-dependent resistor. It outputs a voltage from the OUT pin that is proportional to the light level. The module is very small:

Use is simple – just measure the value returned from the OUT pin using an analogue input pin on your Arduino (etc). For more information please visit the product page. And finally, the:

Sound and Buzzer Module

This module contains a piezoelectric element that can be used to generate sounds (in the form of musical buzzes…):

Driving the buzzer is simple, just use pulse-width modulation. Arduino users can find a good demonstration of this here. Furthermore, as piezoelectric elements can also generate a small electrical current when vibrated, they can be used as “shock” detectors by measuring the voltage across the terminals of the element. The procedure to do this is also explained clearly here.

Now for a final demonstration – we use the light sensor to demonstrate making some noise with the buzzer module:

One final note I would like to make is that the design and construction quality of each module is first rate. The PCBs are strong, and the silk-screening is useful and descriptive. If you find the need for some or all of the functions made available in this range, you could do worse by not considering a Freetronics unit. Finally, although this has only been a short introduction to the modules for now, we will make use of them in later projects.

The modules are available directly from Freetronics or through their network of resellers.

Disclaimer – Modules reviewed in this article are a promotional consideration made available by Freetronics

Have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column, or join our Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, freetronics, learning electronics, microcontrollers, modules, reviewComments (0)


Subscribe via email

Receive notifications of new posts by email.

The Arduino Book

Arduino Workshop

Für unsere deutschen Freunde

Dla naszych polskich przyjaciół ...

Australian Electronics!

Buy and support Silicon Chip - Australia's only Electronics Magazine.

Use of our content…

%d bloggers like this: