Tag Archive | "pong"

Kit review – nootropic design Hackvision

Hello readers

Time for another kit review – the nootropics design Hackvision,  a nice change from test equipment. The purpose of the Hackvision is to allow the user to create retro-style arcade games and so on that can be played on a monitor or television set with analogue video input. Although the display resolution is only 128 by 96 pixels, this is enough to get some interesting action happening. Frankly I didn’t think the Arduino hardware environment alone was capable of this, so the Hackvision was a pleasant surprise.

Assembly is quick and relatively simple, the instructions are online and easy to follow. All the parts required are included:

partsss

The microcontroller is pre-loaded with two games so you can start playing once construction has finished. However you will need a 5V FTDI cable if you wish to upload new games as the board does not have a USB interface. The board is laid out very clearly, and with the excellent silk-screen and your eyes open construction will be painless. Note that you don’t need to install R4 unless necessary, and if your TV system is PAL add the link which is between the RCA sockets. Speaking of which, when soldering them in, bend down the legs to lock them in before soldering, as such:

Doing so will keep them nicely flush with the PCB whilst soldering. Once finished you should have something like this:

almostdoness

All there is to do now is click the button covers into place, plug in your video and audio RCA leads to a monitor, insert nine volts of DC power, and go:

doness

Nice one. For the minimalist users out there, be careful if playing games as the solder on the rear of the PCB can be quite sharp. Included with the kit is some adhesive rubber matting to attach to the underside to smooth everything off nicely. However only fit this once you have totally finished with soldering and modifying the board, otherwise it could prove difficult to remove neatly later on. Time to play some gamesin the following video you can see how poor my reflexes are when playing Pong and Space Invaders:

[ … the Hackvision also generates sounds, however my cheap $10 video capture dongle from eBay didn’t come through with the audio … ]

Well that takes me back. There are some more contemporary games and demonstration code available on the Hackvision games web page. For the more involved Hackvision gamer, there are points on the PCB to attach your own hand-held controls such as paddles, nunchuks and so on. There is a simple tutorial on how to make your own paddles here.

Those who have been paying attention will have noticed that although the Hackvision PCB is not the standard Arduino Duemilanove-compatible layout, all the electronics are there. Apart from I/O pins used by the game buttons, you have a normal Arduino-style board with video and audio out. This opens up a whole world of possibilities with regards to the display of data in your own Arduino sketches (software). From a power supply perspective, note that the regulator is a 78L05 which is only good for 100mA of current, and the board itself uses around 25mA.

To control the video output, you will need to download and install the hackvision-version arduino-tvout library. Note that this library is slightly different to the generic arduino-tvout library with regards to function definitions and parameters. To make use of the included buttons easier, there is also the controllers library. Here is a simple, relatively self-explanatory sketch that demonstrates some uses of the tvout functions:

And the resulting video demonstration:

I will be the first to admit that my imagination is lacking some days. However with the sketch above hopefully you can get a grip on how the functions work. But there are some very good game implementations out there, as listed on the Hackvision games page. After spending some time with this kit, I feel that there is a lack of documentation that is easy to get into. Sure, having some great games published is good but some beginners’ tutorials would be nice as well. However if you have the time and the inclination, there is much that could be done. In the meanwhile you can do your own sleuthing with regards to the functions by examining the TVout.cpp file in the Hackvision tvout library folder.

For further questions about the Hackvision contact nootropic design or perhaps post on their forum. However the Hackvision has a lot of potential and is an interesting extension of the Arduino-based hardware universe – another way to send data to video monitors and televisions, and play some fun games.If you are looking for a shield-based video output device, perhaps consider the Batsocks Tellymate.

As always, thank you for reading and I look forward to your comments and so on. Furthermore, don’t be shy in pointing out errors or places that could use improvement. Please subscribe using one of the methods at the top-right of this web page to receive updates on new posts, follow me on twitter or facebook, or join our Google Group for further discussion.

High resolution images are available on flickr.

[Note – The kit was purchased by myself personally and reviewed without notifying the manufacturer or retailer]

Posted in arduino, games, hackvision, kit review, LCD, microcontrollers, notropicsComments (2)

Blinky the one-eyed clock

In this tutorial you learn how to make a blinking clock with a difference!

Updated 18/03/2013

Followers of my website would realise that I tend to make too many clocks in those tutorials. Well, I like making clocks… so here is another one. However this time I have tried to make the most simple version possible. Usually projects will have many LEDs, or perhaps an LCD, buzzers, buttons, all sorts of things. Which looks great and will impress many. But the other day I thought to myself … “how few things do you need to show the time?”

So here is my answer to that question: Blinky the one-eyed clock …

workingsss

It reminds me of the giant killer orb from The Prisoner… Using a minimal Arduino bootloader system, a DS1307 real time clock IC and an RGB diffused LED … we can make a clock that blinks the time, using the colours of the LED to note different numerical values. For example, if the time is 12:45, the clock will blink red 12 times, then show blue for a second (think of this as the colon on a digital clock) then blink four times in green (for forty minutes), then blink three times in red for the individual minutes. If there is a zero, blink blue quickly. Then the clock will not display anything for around forty seconds, then repeat the process. Here he (she, it?) is blinking the time:

Setting the clock is simple. It is set to start at 12:00 upon power up. So for the first use you have to wait until about five seconds before midday or midnight, then power it up. To save cost it doesn’t use a backup lithium battery on the real-time clock IC, but you could if you really wanted to. If you would like to follow my design process narrative, please read on. If you only want the sketch and schematic, 🙁 head to the bottom of this article.

Design process narrative…

So let’s get started!

The first thing to do was test the RGB LED for brightness levels, so I just connected it to the digital output pins of my Eleven via suitable current-limiting resistors. Each LED is going to be different, so to ensure maximum brightness without causing any damage you need to calculate the appropriate resistor values. This is quite easy, the formula is: resistor (ohms) = voltage drop / LED current So if you have a 5 V supply, and LED that needs only 2 volts, and draws 20 milliamps (0.2 amps) , the calculation will be: resistor = (5-2)/0.02 = 150 ohms. To be safe I used a 180 ohm resistor. The LED was tested with this simple sketch:

It was interesting to alter the value of d, the delay variable, to get an idea for an appropriate blinking speed. Originally the plan was to have the LED in a photo frame, but it was decided to mount a ping-pong ball over the LED for a retro-style look.  Here is a short video of the result of the test:

If you are going to use a ping-pong ball, please be careful when cutting into it with a knife, initially it may require a lot of force, but once the knife cuts through it does so very quickly:

cuttingppballss

Now it was time to develop the sketch to convert time into blinks. The sketch itself is quite simple. Read the hours and minutes from the DS1307 timer IC; convert the hours to 12 hour time; then blink an LED for the number of hours, display another colour for the colon; divide the minutes by ten and blink that in another colour; then the modulus of minutes and ten to find the individual minutes, and blink those out. Here is the first sketch I came up with. Finally, the code was tested using the Eleven board and my DS1307 real time clock shield. It is best to use existing hardware while testing, before committing to purchasing new hardware and so on. So here it is on the breadboard:

workingprototype1ss

And telling the time! In this example, the time is 3:45…

But perhaps that was a little bland. By using analogWrite() we can control the brightness of the LED segments. So now there are two more functions, whiteGlow() and blueGlow(); whose purpose is to make the display “glow” by increasing then decreasing the brightness. And scale back the amount of blinking, to increase battery life and make blinky less obvious. So now the display will glow white to announce the forthcoming display of time, wait a second, blink the time (with a blue glowing colon) then stay dark for ten seconds before repeating the process. Here is a quick demonstration of this display style:

Here is the sketch for the above demonstration, and the final one I will use with the hardware prototype. Once happy with the sketch, I put a fresh ATmega328 with Arduino bootloader in the board and programmed it with the blinky sketch, to be used in the final product.

Next was to build my own hardware. My last hardware unknown is the amount of current the circuit draws. Once I know this the correct voltage regulator and power supply can be decided upon. I had a fair idea it would be less than 100 milliamps, so I put a 6V battery onto supply duty via a 78L05 5V regulator (data sheet), and recorded the result:

So it varies, between 20.5 and 46 mA. As it only reaches 46 mA for a short time, we could consider the constant draw to be averaged out at 30 mA. I really want this to be able to run from a battery, but without having an external lead-acid battery lurking around, it will need a plug-pack with an output voltage greater than 7V DC. Another alternative would be to run it from a USB socket, a nice source of 5V. If doing so, there wouldn’t be a need for the 78L05 regulator. Which brings us to the  circuit diagram, which includes the power regulator:

blinkyschematicss

 

It does not allow for programming in the circuit, so you will need to program the microcontroller on another Arduino or compatible board, then transfer it to the blinky circuit board as described above. At this stage I tested it again, but using a solderless breadboard. In doing so you can make final hardware checks, and  generally make sure everything works as it should. This is also a good stage to double-check you are happy with the display behaviour, default time and so on.

breadboardedss

Time to solder up the circuit on some stripboard. Blank stripboard varies, but luckily I found this and a nice box to hold it in:

boxandpcbss

Stripboard does vary between retailers and so on, so you will need to work out the layout with your own board. In doing so, please double-check your work – follow the layout against the schematic and so on. Have a break, then check it again. There is nothing worse than soldering away to realise you are one strip too far over or something. My hand-eye coordination is not the best, therefore my soldering isn’t pretty, but it works:

solderedfrontss

 

solderedrearss

One would say that there is a good argument for making your own PCBs… and I would start to agree with that. The LED is soldered to some short leads to give it a bit of play, and some heatshrink over the legs to keep them isolated:

heatshrinkledss

 

And finally, to add a DC socket to feed blinky some power…

finalbaress

 

The last thing was to check the soldering once more under natural light, to check for bridges or shorts, then have a cup of tea. Upon my return I drilled out a hole in the enclosure lid for the LED, and one one the side for the DC socket, and fitted the lot together… and success! It worked 🙂

So there you have it. The journey from a daydream to a finished product… well a prototype anyway. But it works, and that is the best feeling of all. You can download the schematic from here. And here is the Arduino sketch:

I hope you enjoyed reading this post and hopefully felt inspired enough to make your own.

In the meanwhile have fun and keep checking into tronixstuff.com. Why not follow things on twitterGoogle+, subscribe  for email updates or RSS using the links on the right-hand column? And join our friendly Google Group – dedicated to the projects and related items on this website. Sign up – it’s free, helpful to each other –  and we can all learn something.

Posted in arduino, clocks, ds1307, microcontrollers, projects, RGB LED, tutorialComments (18)


Subscribe via email

Receive notifications of new posts by email.

The Arduino Book

Arduino Workshop

Für unsere deutschen Freunde

Dla naszych polskich przyjaciół ...

Australian Electronics!

Buy and support Silicon Chip - Australia's only Electronics Magazine.

Use of our content…

%d bloggers like this: